58 lines
1.8 KiB
Lua
58 lines
1.8 KiB
Lua
|
---
|
||
|
|
-- @description Shows how to read 8 GPIO pins/buttons via I2C with the MCP23008 I/O expander.
|
||
|
|
-- Tested on NodeMCU 0.9.5 build 20150213.
|
||
|
|
-- @circuit
|
||
|
|
-- Connect GPIO0 of the ESP8266-01 module to the SCL pin of the MCP23008.
|
||
|
|
-- Connect GPIO2 of the ESP8266-01 module to the SDA pin of the MCP23008.
|
||
|
|
-- Use 3.3V for VCC.
|
||
|
|
-- Connect switches or buttons to the GPIOs of the MCP23008 and GND.
|
||
|
|
-- Connect two 4.7k pull-up resistors on SDA and SCL
|
||
|
|
-- We will enable the internal pull up resistors for the GPIOS of the MCP23008.
|
||
|
|
-- @author Miguel (AllAboutEE)
|
||
|
|
-- GitHub: https://github.com/AllAboutEE
|
||
|
|
-- YouTube: https://www.youtube.com/user/AllAboutEE
|
||
|
|
-- Website: http://AllAboutEE.com
|
||
|
|
---------------------------------------------------------------------------------------------
|
||
|
|
|
||
|
|
require ("mcp23008")
|
||
|
|
|
||
|
|
-- ESP-01 GPIO Mapping as per GPIO Table in https://github.com/nodemcu/nodemcu-firmware
|
||
|
|
gpio0, gpio2 = 3, 4
|
||
|
|
|
||
|
|
-- Setup the MCP23008
|
||
|
|
mcp23008.begin(0x0,gpio2,gpio0,i2c.SLOW)
|
||
|
|
|
||
|
|
mcp23008.writeIODIR(0xff)
|
||
|
|
mcp23008.writeGPPU(0xff)
|
||
|
|
|
||
|
|
---
|
||
|
|
-- @name showButtons
|
||
|
|
-- @description Shows the state of each GPIO pin
|
||
|
|
-- @return void
|
||
|
|
---------------------------------------------------------
|
||
|
|
function showButtons()
|
||
|
|
|
||
|
|
local gpio = mcp23008.readGPIO() -- read the GPIO/buttons states
|
||
|
|
|
||
|
|
-- get/extract the state of one pin at a time
|
||
|
|
for pin=0,7 do
|
||
|
|
|
||
|
|
local pinState = bit.band(bit.rshift(gpio,pin),0x1) -- extract one pin state
|
||
|
|
|
||
|
|
-- change to string state (HIGH, LOW) instead of 1 or 0 respectively
|
||
|
|
if(pinState == mcp23008.HIGH) then
|
||
|
|
pinState = "HIGH"
|
||
|
|
else
|
||
|
|
pinState = "LOW"
|
||
|
|
end
|
||
|
|
|
||
|
|
print("Pin ".. pin .. ": ".. pinState)
|
||
|
|
end
|
||
|
|
print("\r\n")
|
||
|
|
end
|
||
|
|
|
||
|
|
tmr.alarm(0,2000,1,showButtons) -- run showButtons() every 2 seconds
|
||
|
|
|
||
|
|
|
||
|
|
|