diff --git a/docs/en/modules/dht.md b/docs/en/modules/dht.md
new file mode 100644
index 00000000..e4958004
--- /dev/null
+++ b/docs/en/modules/dht.md
@@ -0,0 +1,93 @@
+# dht Module
+
+## Constants
+`dht.OK` (0), `dht.ERROR_CHECKSUM` (1), `dht.ERROR_TIMEOUT` (2)
+
+## dht.read()
+Read all kinds of DHT sensors, including DHT11, 21, 22, 33, 44 humidity temperature combo sensor.
+
+#### Syntax
+`dht.read(pin)`
+
+#### Parameters
+`pin` pin number of DHT sensor (can't be 0), type is number
+
+#### Returns
+- `status` as defined in Constants
+- `temp` temperature (see note below)
+- `humi` humidity (see note below)
+- `temp_dec` temperature decimal
+- `humi_dec` humidity decimal
+
+!!! note "Note:"
+
+If using float firmware then `temp` and `humi` are floating point numbers. On an integer firmware, the final values have to be concatenated from `temp` and `temp_dec` / `humi` and `hum_dec`.
+
+#### Example
+```lua
+pin = 5
+status, temp, humi, temp_dec, humi_dec = dht.read(pin)
+if status == dht.OK then
+    -- Integer firmware using this example
+    print(string.format("DHT Temperature:%d.%03d;Humidity:%d.%03d\r\n",
+          math.floor(temp),
+          temp_deci,
+          math.floor(humi),
+          humi_deci
+    ))
+
+    -- Float firmware using this example
+    print("DHT Temperature:"..temp..";".."Humidity:"..humi)
+
+elseif status == dht.ERROR_CHECKSUM then
+    print( "DHT Checksum error." )
+elseif status == dht.ERROR_TIMEOUT then
+    print( "DHT timed out." )
+end
+```
+
+## dht.read11()
+Read DHT11 humidity temperature combo sensor.
+
+#### Syntax
+`dht.read11(pin)`
+
+#### Parameters
+`pin` pin number of DHT11 sensor (can't be 0), type is number
+
+#### Returns
+- `status` as defined in Constants
+- `temp` temperature (see note below)
+- `humi` humidity (see note below)
+- `temp_dec` temperature decimal
+- `humi_dec` humidity decimal
+
+!!! note "Note:"
+
+If using float firmware then `temp` and `humi` are floating point numbers. On an integer firmware, the final values have to be concatenated from `temp` and `temp_dec` / `humi` and `hum_dec`.
+
+#### See also
+[dht.read()](#dhtread)
+
+## dht.readxx()
+Read all kinds of DHT sensors, except DHT11.
+
+####Syntax
+`dht.readxx(pin)`
+
+#### Parameters
+`pin` pin number of DHT sensor (can't be 0), type is number
+
+#### Returns
+- `status` as defined in Constants
+- `temp` temperature (see note below)
+- `humi` humidity (see note below)
+- `temp_dec` temperature decimal
+- `humi_dec` humidity decimal
+
+!!! note "Note:"
+
+If using float firmware then `temp` and `humi` are floating point numbers. On an integer firmware, the final values have to be concatenated from `temp` and `temp_dec` / `humi` and `hum_dec`.
+
+#### See also
+[dht.read()](#dhtread)
diff --git a/mkdocs.yml b/mkdocs.yml
index fbfb1e73..c421b034 100644
--- a/mkdocs.yml
+++ b/mkdocs.yml
@@ -33,6 +33,7 @@ pages:
         - 'bit': 'en/modules/bit.md'
         - 'cjson': 'en/modules/cjson.md'
         - 'crypto': 'en/modules/crypto.md'
+        - 'dht': 'en/modules/dht.md'
         - 'enduser setup': 'en/modules/enduser-setup.md'
         - 'file': 'en/modules/file.md'
         - 'gpio': 'en/modules/gpio.md'