158 lines
4.3 KiB
Lua
158 lines
4.3 KiB
Lua
-- ***************************************************************************
|
||
-- DHTxx(11,21,22) module for ESP8266 with nodeMCU
|
||
--
|
||
-- Written by Javier Yanez mod by Martin
|
||
-- but based on a script of Pigs Fly from ESP8266.com forum
|
||
--
|
||
-- MIT license, http://opensource.org/licenses/MIT
|
||
-- ***************************************************************************
|
||
|
||
--Support list：
|
||
--DHT11 Tested ->read11
|
||
--DHT21 Not Tested->read22
|
||
--DHT22 Tested->read22
|
||
|
||
--==========================Module Part======================
|
||
local moduleName = ...
|
||
local M = {}
|
||
_G[moduleName] = M
|
||
--==========================Local the UMI and TEMP===========
|
||
local humidity
|
||
local temperature
|
||
--==========================Local the bitStream==============
|
||
local bitStream = {}
|
||
|
||
---------------------------Read bitStream from DHTXX--------------------------
|
||
local function read(pin)
|
||
|
||
local bitlength = 0
|
||
humidity = 0
|
||
temperature = 0
|
||
|
||
-- Use Markus Gritsch trick to speed up read/write on GPIO
|
||
local gpio_read = gpio.read
|
||
|
||
|
||
for j = 1, 40, 1 do
|
||
bitStream[j] = 0
|
||
end
|
||
|
||
|
||
|
||
-- Step 1: send out start signal to DHT22
|
||
gpio.mode(pin, gpio.OUTPUT)
|
||
gpio.write(pin, gpio.HIGH)
|
||
tmr.delay(100)
|
||
gpio.write(pin, gpio.LOW)
|
||
tmr.delay(20000)
|
||
gpio.write(pin, gpio.HIGH)
|
||
gpio.mode(pin, gpio.INPUT)
|
||
|
||
-- Step 2: Receive bitStream from DHT11/22
|
||
-- bus will always let up eventually, don't bother with timeout
|
||
while (gpio_read(pin) == 0 ) do end
|
||
local c=0
|
||
while (gpio_read(pin) == 1 and c < 500) do c = c + 1 end
|
||
-- bus will always let up eventually, don't bother with timeout
|
||
while (gpio_read(pin) == 0 ) do end
|
||
c=0
|
||
while (gpio_read(pin) == 1 and c < 500) do c = c + 1 end
|
||
|
||
-- Step 3: DHT22 send data
|
||
for j = 1, 40, 1 do
|
||
while (gpio_read(pin) == 1 and bitlength < 10 ) do
|
||
bitlength = bitlength + 1
|
||
end
|
||
bitStream[j] = bitlength
|
||
bitlength = 0
|
||
-- bus will always let up eventually, don't bother with timeout
|
||
while (gpio_read(pin) == 0) do end
|
||
end
|
||
end
|
||
---------------------------Convert the bitStream into Number through DHT11 Ways--------------------------
|
||
function M.read11(pin)
|
||
--As for DHT11 40Bit is consisit of 5Bytes
|
||
--First byte->Humidity Data's Int part
|
||
--Sencond byte->Humidity Data's Float Part(Which should be empty)
|
||
--Third byte->Temp Data;s Intpart
|
||
--Forth byte->Temp Data's Float Part(Which should be empty)
|
||
--Fifth byte->SUM Byte, Humi+Temp
|
||
read(pin)
|
||
local checksum = 0
|
||
local checksumTest
|
||
--DHT data acquired, process.
|
||
for i = 1, 8, 1 do -- Byte[0]
|
||
if (bitStream[i] > 3) then
|
||
humidity = humidity + 2 ^ (8 - i)
|
||
end
|
||
end
|
||
for i = 1, 8, 1 do -- Byte[2]
|
||
if (bitStream[i + 16] > 3) then
|
||
temperature = temperature + 2 ^ (8 - i)
|
||
end
|
||
end
|
||
for i = 1, 8, 1 do --Byte[4]
|
||
if (bitStream[i + 32] > 3) then
|
||
checksum = checksum + 2 ^ (8 - i)
|
||
end
|
||
end
|
||
|
||
if(checksum ~= humidity+temperature) then
|
||
humidity = nil
|
||
temperature = nil
|
||
end
|
||
|
||
end
|
||
---------------------------Convert the bitStream into Number through DHT22 Ways--------------------------
|
||
function M.read22( pin )
|
||
--As for DHT22 40Bit is consisit of 5Bytes
|
||
--First byte->Humidity Data's High Bit
|
||
--Sencond byte->Humidity Data's Low Bit(And if over 0x8000, use complement)
|
||
--Third byte->Temp Data's High Bit
|
||
--Forth byte->Temp Data's Low Bit
|
||
--Fifth byte->SUM Byte
|
||
read(pin)
|
||
local checksum = 0
|
||
local checksumTest
|
||
--DHT data acquired, process.
|
||
for i = 1, 16, 1 do
|
||
if (bitStream[i] > 3) then
|
||
humidity = humidity + 2 ^ (16 - i)
|
||
end
|
||
end
|
||
for i = 1, 16, 1 do
|
||
if (bitStream[i + 16] > 3) then
|
||
temperature = temperature + 2 ^ (16 - i)
|
||
end
|
||
end
|
||
for i = 1, 8, 1 do
|
||
if (bitStream[i + 32] > 3) then
|
||
checksum = checksum + 2 ^ (8 - i)
|
||
end
|
||
end
|
||
|
||
checksumTest = (bit.band(humidity, 0xFF) + bit.rshift(humidity, 8) + bit.band(temperature, 0xFF) + bit.rshift(temperature, 8))
|
||
checksumTest = bit.band(checksumTest, 0xFF)
|
||
|
||
if temperature > 0x8000 then
|
||
-- convert to negative format
|
||
temperature = -(temperature - 0x8000)
|
||
end
|
||
|
||
-- conditions compatible con float point and integer
|
||
if (checksumTest - checksum >= 1) or (checksum - checksumTest >= 1) then
|
||
humidity = nil
|
||
end
|
||
end
|
||
|
||
---------------------------Check out the data--------------------------
|
||
function M.getTemperature()
|
||
return temperature
|
||
end
|
||
|
||
function M.getHumidity()
|
||
return humidity
|
||
end
|
||
|
||
return M
|