160 lines
6.5 KiB
Plaintext
160 lines
6.5 KiB
Plaintext
menu "NodeMCU platform config"
|
|
|
|
config NODEMCU_NODE_DEBUG
|
|
bool "Enable NODE_DBG() output"
|
|
default "n"
|
|
help
|
|
Enable debugging output via NODE_DBG(). This is VERY chatty.
|
|
For development/debugging use only.
|
|
|
|
config NODEMCU_NODE_ERR
|
|
bool "Enable NODE_ERR() output"
|
|
default "y"
|
|
help
|
|
Enable error reporting via NODE_ERR().
|
|
|
|
It is recommended to leave this enabled - if it ever produces
|
|
output, something has gone seriously wrong and you probably want
|
|
to know about it.
|
|
|
|
config NODEMCU_DEFAULT_SPIFFS_LABEL
|
|
string "Partition label of SPIFFS to mount as default file system"
|
|
default ""
|
|
help
|
|
If there are multiple SPIFFS partitions, this setting can
|
|
be used to control which partition gets mounted as the
|
|
default file system. Leaving it empty defaults to using
|
|
the first SPIFFS partition found.
|
|
|
|
config NODEMCU_MAX_OPEN_FILES
|
|
int "Maximum number of open files"
|
|
default 4
|
|
help
|
|
This sets the maximum number of open files at the same time.
|
|
Technically, it's per file system, but the most common use
|
|
case only has a single file system (internal SPIFFS) so in
|
|
that case it is the number of concurrent files that can be
|
|
opened. Raising this limit will incur some extra memory
|
|
overhead.
|
|
|
|
config NODEMCU_AUTO_FORMAT_ON_BOOT
|
|
bool "Auto-format SPIFFS on first boot"
|
|
default "y" if !ESP_CONSOLE_USB_CDC
|
|
default "n" if ESP_CONSOLE_USB_CDC
|
|
help
|
|
The traditional behavior of NodeMCU is to automatically format
|
|
the SPIFFS partition on first boot (or any other time the
|
|
filesystem is unmountable). When using USB CDC however, the
|
|
formatting can interfere with USB device enumeration, leading
|
|
to a failed boot. In that case, disable the auto-format and
|
|
use file.format() after startup instead.
|
|
|
|
config NODEMCU_EMBED_LFS
|
|
bool "Embed LFS as part of the NodeMCU firmware"
|
|
default "n"
|
|
help
|
|
The LFS (Lua Flash Store) normally has its own partition entry,
|
|
and can can be replaced at will. Optionally, the LFS can instead
|
|
be permanently embedded into the NodeMCU firmware image itself.
|
|
This can be useful for scenarios where over-the-air firmware
|
|
upgrades are needed to also bundle Lua code. The major downside
|
|
is that once embedded, the LFS can no longer be changed, as
|
|
doing so would break the firmware checksums and signatures and
|
|
leave the system unable to boot.
|
|
|
|
The default option is to not embed the LFS, in which case LFS is
|
|
looked for in a partition of type 0xC2 and subtype 0x01.
|
|
|
|
To embed LFS data into firmware, use:
|
|
./tools/embed_lfs.sh /path/to/file1.lua /path/to/file2.lua ...
|
|
|
|
config NODEMCU_EMBEDDED_LFS_SIZE
|
|
hex "Embedded LUA Flash Store size"
|
|
default 0x0
|
|
depends on NODEMCU_EMBED_LFS
|
|
help
|
|
Embedded LUA Flash Store size. Set to zero to use an LFS partition
|
|
instead of embedding the LFS within the NodeMCU firmware itself.
|
|
|
|
menu "UART buffer size configuration"
|
|
|
|
config NODEMCU_UART_AT_LEAST_2
|
|
bool
|
|
default y if IDF_TARGET_ESP32
|
|
default y if IDF_TARGET_ESP32S2
|
|
default y if IDF_TARGET_ESP32S3
|
|
default y if IDF_TARGET_ESP32C3
|
|
default y if IDF_TARGET_ESP32C6
|
|
default y if IDF_TARGET_ESP32H2
|
|
|
|
config NODEMCU_UART_AT_LEAST_3
|
|
bool
|
|
default y if IDF_TARGET_ESP32
|
|
default y if IDF_TARGET_ESP32S3
|
|
default y if IDF_TARGET_ESP32C6
|
|
|
|
config NODEMCU_UART_DRIVER_BUF_SIZE_RX0
|
|
int "RX buffer size for UART0"
|
|
default 512
|
|
help
|
|
The rx buffer size to use for UART0.
|
|
This is a buffer used to/from the UART ISR. For high-speed scenarios,
|
|
it can be very helpful to increase the rx size. The ISR trying
|
|
to write to a full rx buffer results in lost data and an error
|
|
event posted.
|
|
|
|
config NODEMCU_UART_DRIVER_BUF_SIZE_TX0
|
|
int "TX buffer size for UART0"
|
|
default 512
|
|
help
|
|
The tx buffer size to use for UART0.
|
|
This is a buffer used to/from the UART ISR. In some scenarios it
|
|
can be helpful to increase the tx size. Writing to a full tx buffer
|
|
blocks the calling RTOS task.
|
|
|
|
config NODEMCU_UART_DRIVER_BUF_SIZE_RX1
|
|
int "RX buffer size for UART1"
|
|
depends on NODEMCU_UART_AT_LEAST_2
|
|
default 512
|
|
help
|
|
The rx buffer size to use for UART1.
|
|
This is a buffer used to/from the UART ISR. For high-speed scenarios,
|
|
it can be very helpful to increase the rx size. The ISR trying
|
|
to write to a full rx buffer results in lost data and an error
|
|
event posted.
|
|
|
|
config NODEMCU_UART_DRIVER_BUF_SIZE_TX1
|
|
int "TX buffer size for UART1"
|
|
depends on NODEMCU_UART_AT_LEAST_2
|
|
default 512
|
|
help
|
|
The tx buffer size to use for UART1.
|
|
This is a buffer used to/from the UART ISR. In some scenarios it
|
|
can be helpful to increase the tx size. Writing to a full tx buffer
|
|
blocks the calling RTOS task.
|
|
|
|
config NODEMCU_UART_DRIVER_BUF_SIZE_RX2
|
|
int "RX buffer size for UART2"
|
|
depends on NODEMCU_UART_AT_LEAST_3
|
|
default 512
|
|
help
|
|
The rx buffer size to use for UART2.
|
|
This is a buffer used to/from the UART ISR. For high-speed scenarios,
|
|
it can be very helpful to increase the rx size. The ISR trying
|
|
to write to a full rx buffer results in lost data and an error
|
|
event posted.
|
|
|
|
config NODEMCU_UART_DRIVER_BUF_SIZE_TX2
|
|
int "TX buffer size for UART2"
|
|
depends on NODEMCU_UART_AT_LEAST_3
|
|
default 512
|
|
help
|
|
The tx buffer size to use for UART2.
|
|
This is a buffer used to/from the UART ISR. In some scenarios it
|
|
can be helpful to increase the tx size. Writing to a full tx buffer
|
|
blocks the calling RTOS task.
|
|
|
|
endmenu
|
|
|
|
endmenu
|