330 lines
9.4 KiB
C
330 lines
9.4 KiB
C
|
|
#include <string.h>
|
|
|
|
#include "rom/ets_sys.h"
|
|
|
|
#include "driver/gpio.h"
|
|
#include "driver/i2c.h"
|
|
#include "driver/spi_master.h"
|
|
#include "platform.h"
|
|
|
|
#include "u8x8_nodemcu_hal.h"
|
|
|
|
#include "esp_heap_alloc_caps.h"
|
|
|
|
|
|
uint8_t u8x8_gpio_and_delay_nodemcu(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
|
|
{
|
|
uint32_t temp;
|
|
|
|
switch(msg)
|
|
{
|
|
case U8X8_MSG_GPIO_AND_DELAY_INIT: // called once during init phase of u8g2/u8x8
|
|
// can be used to setup pins
|
|
for (int idx = 0; idx < U8X8_PIN_OUTPUT_CNT; idx++) {
|
|
if (u8x8->pins[idx] != U8X8_PIN_NONE) {
|
|
// configure pin as output
|
|
gpio_config_t cfg;
|
|
memset( (void *)&cfg, 0, sizeof( cfg ) );
|
|
cfg.pin_bit_mask = 1ULL << u8x8->pins[idx];
|
|
|
|
if (idx == U8X8_PIN_I2C_CLOCK || idx == U8X8_PIN_I2C_CLOCK) {
|
|
cfg.mode = GPIO_MODE_OUTPUT_OD;
|
|
cfg.pull_up_en = GPIO_PULLUP_ENABLE;
|
|
} else {
|
|
cfg.mode = GPIO_MODE_OUTPUT;
|
|
cfg.pull_up_en = GPIO_PULLUP_DISABLE;
|
|
}
|
|
cfg.pull_down_en = GPIO_PULLDOWN_DISABLE;
|
|
cfg.intr_type = GPIO_INTR_DISABLE;
|
|
gpio_config( &cfg );
|
|
}
|
|
}
|
|
break;
|
|
|
|
case U8X8_MSG_DELAY_NANO: // delay arg_int * 1 nano second
|
|
ets_delay_us( 1 );
|
|
break;
|
|
|
|
case U8X8_MSG_DELAY_100NANO: // delay arg_int * 100 nano seconds
|
|
temp = arg_int * 100;
|
|
temp /= 1000;
|
|
ets_delay_us( temp > 0 ? temp : 1 );
|
|
break;
|
|
|
|
case U8X8_MSG_DELAY_10MICRO: // delay arg_int * 10 micro seconds
|
|
ets_delay_us( arg_int * 10 );
|
|
break;
|
|
|
|
case U8X8_MSG_DELAY_MILLI: // delay arg_int * 1 milli second
|
|
ets_delay_us( arg_int * 1000 );
|
|
break;
|
|
|
|
case U8X8_MSG_DELAY_I2C: // arg_int is the I2C speed in 100KHz, e.g. 4 = 400 KHz
|
|
temp = 5000 / arg_int; // arg_int=1: delay by 5us, arg_int = 4: delay by 1.25us
|
|
temp /= 1000;
|
|
ets_delay_us( temp > 0 ? temp : 1 );
|
|
break;
|
|
|
|
case U8X8_MSG_GPIO_D0: // D0 or SPI clock pin: Output level in arg_int
|
|
//case U8X8_MSG_GPIO_SPI_CLOCK:
|
|
break;
|
|
case U8X8_MSG_GPIO_D1: // D1 or SPI data pin: Output level in arg_int
|
|
//case U8X8_MSG_GPIO_SPI_DATA:
|
|
break;
|
|
case U8X8_MSG_GPIO_D2: // D2 pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_D3: // D3 pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_D4: // D4 pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_D5: // D5 pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_D6: // D6 pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_D7: // D7 pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_E: // E/WR pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_CS: // CS (chip select) pin: Output level in arg_int
|
|
gpio_set_level( u8x8_GetPinValue( u8x8, msg ), arg_int );
|
|
break;
|
|
case U8X8_MSG_GPIO_DC: // DC (data/cmd, A0, register select) pin: Output level in arg_int
|
|
gpio_set_level( u8x8_GetPinValue( u8x8, msg ), arg_int );
|
|
break;
|
|
case U8X8_MSG_GPIO_RESET: // Reset pin: Output level in arg_int
|
|
if (u8x8_GetPinValue( u8x8, msg ) != U8X8_PIN_NONE)
|
|
gpio_set_level( u8x8_GetPinValue(u8x8, msg), arg_int );
|
|
break;
|
|
case U8X8_MSG_GPIO_CS1: // CS1 (chip select) pin: Output level in arg_int
|
|
break;
|
|
case U8X8_MSG_GPIO_CS2: // CS2 (chip select) pin: Output level in arg_int
|
|
break;
|
|
|
|
case U8X8_MSG_GPIO_I2C_CLOCK: // arg_int=0: Output low at I2C clock pin
|
|
// arg_int=1: Input dir with pullup high for I2C clock pin
|
|
// for SW comm routine
|
|
gpio_set_level( u8x8_GetPinValue( u8x8, msg ), arg_int );
|
|
break;
|
|
|
|
case U8X8_MSG_GPIO_I2C_DATA: // arg_int=0: Output low at I2C data pin
|
|
// arg_int=1: Input dir with pullup high for I2C data pin
|
|
// for SW comm routine
|
|
gpio_set_level( u8x8_GetPinValue( u8x8, msg ), arg_int );
|
|
break;
|
|
|
|
case U8X8_MSG_GPIO_MENU_SELECT:
|
|
case U8X8_MSG_GPIO_MENU_NEXT:
|
|
case U8X8_MSG_GPIO_MENU_PREV:
|
|
case U8X8_MSG_GPIO_MENU_HOME:
|
|
u8x8_SetGPIOResult( u8x8, /* get menu select pin state */ 0 );
|
|
break;
|
|
default:
|
|
u8x8_SetGPIOResult( u8x8, 1 ); // default return value
|
|
break;
|
|
}
|
|
return 1;
|
|
}
|
|
|
|
|
|
// static variables containing info about the i2c link
|
|
// TODO: move to user space in u8x8_t once available
|
|
typedef struct {
|
|
uint8_t id;
|
|
i2c_cmd_handle_t cmd;
|
|
struct {
|
|
uint8_t *data;
|
|
size_t size, used;
|
|
} buffer;
|
|
} hal_i2c_t;
|
|
|
|
uint8_t u8x8_byte_nodemcu_i2c(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
|
|
{
|
|
uint8_t *data;
|
|
hal_i2c_t *hal = ((u8g2_nodemcu_t *)u8x8)->hal;
|
|
|
|
switch(msg) {
|
|
case U8X8_MSG_BYTE_SEND:
|
|
if (hal->id == 0) {
|
|
data = (uint8_t *)arg_ptr;
|
|
|
|
while( arg_int > 0 ) {
|
|
platform_i2c_send_byte( 0, *data, 0 );
|
|
data++;
|
|
arg_int--;
|
|
}
|
|
|
|
} else {
|
|
while (hal->buffer.size - hal->buffer.used < arg_int) {
|
|
hal->buffer.size *= 2;
|
|
if (!(hal->buffer.data = (uint8_t *)realloc( hal->buffer.data, hal->buffer.size )))
|
|
return 0;
|
|
}
|
|
memcpy( hal->buffer.data + hal->buffer.used, arg_ptr, arg_int );
|
|
hal->buffer.used += arg_int;
|
|
}
|
|
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_INIT:
|
|
{
|
|
// the hal member initially contains the i2c id
|
|
int id = (int)hal;
|
|
if (!(hal = malloc( sizeof ( hal_i2c_t ) )))
|
|
return 0;
|
|
hal->id = id;
|
|
((u8g2_nodemcu_t *)u8x8)->hal = hal;
|
|
}
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_SET_DC:
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_START_TRANSFER:
|
|
if (hal->id == 0) {
|
|
platform_i2c_send_start( 0 );
|
|
platform_i2c_send_address( 0, u8x8_GetI2CAddress(u8x8), PLATFORM_I2C_DIRECTION_TRANSMITTER, 0 );
|
|
|
|
} else {
|
|
hal->buffer.size = 256;
|
|
if (!(hal->buffer.data = (uint8_t *)malloc( hal->buffer.size )))
|
|
return 0;
|
|
hal->buffer.used = 0;
|
|
|
|
hal->cmd = i2c_cmd_link_create();
|
|
i2c_master_start( hal->cmd );
|
|
i2c_master_write_byte( hal->cmd, u8x8_GetI2CAddress(u8x8) << 1 | I2C_MASTER_WRITE, false );
|
|
}
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_END_TRANSFER:
|
|
if (hal->id == 0) {
|
|
platform_i2c_send_stop( 0 );
|
|
|
|
} else {
|
|
if (hal->buffer.used > 0)
|
|
i2c_master_write( hal->cmd, hal->buffer.data, hal->buffer.used, false );
|
|
|
|
i2c_master_stop( hal->cmd );
|
|
i2c_master_cmd_begin(hal->id-1, hal->cmd, portMAX_DELAY );
|
|
|
|
if (hal->buffer.data)
|
|
free( hal->buffer.data );
|
|
i2c_cmd_link_delete( hal->cmd );
|
|
}
|
|
break;
|
|
|
|
default:
|
|
return 0;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
|
|
// static variables containing info about the spi link
|
|
// TODO: move to user space in u8x8_t once available
|
|
typedef struct {
|
|
uint8_t host;
|
|
spi_device_handle_t device;
|
|
uint8_t last_dc;
|
|
struct {
|
|
uint8_t *data;
|
|
size_t size, used;
|
|
} buffer;
|
|
} hal_spi_t;
|
|
|
|
static void flush_buffer_spi( hal_spi_t *hal )
|
|
{
|
|
if (hal->buffer.used > 0) {
|
|
spi_transaction_t trans;
|
|
memset( &trans, 0, sizeof( trans ) );
|
|
trans.length = hal->buffer.used * 8;
|
|
trans.tx_buffer = hal->buffer.data;
|
|
spi_device_transmit( hal->device, &trans );
|
|
|
|
hal->buffer.used = 0;
|
|
}
|
|
}
|
|
|
|
uint8_t u8x8_byte_nodemcu_spi(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
|
|
{
|
|
hal_spi_t *hal = ((u8g2_nodemcu_t *)u8x8)->hal;
|
|
|
|
switch(msg) {
|
|
case U8X8_MSG_BYTE_INIT:
|
|
{
|
|
/* disable chipselect */
|
|
u8x8_gpio_SetCS( u8x8, u8x8->display_info->chip_disable_level );
|
|
|
|
// the hal member initially contains the spi host id
|
|
int host = (int)hal;
|
|
if (!(hal = malloc( sizeof ( hal_spi_t ) )))
|
|
return 0;
|
|
hal->host = host;
|
|
((u8g2_nodemcu_t *)u8x8)->hal = hal;
|
|
|
|
// set up the spi device
|
|
spi_device_interface_config_t config;
|
|
memset( &config, 0, sizeof( config ) );
|
|
|
|
config.spics_io_num = -1; // CS is controlled by u8x8 gpio mechanism
|
|
config.mode = u8x8_GetSPIClockPhase( u8x8 ) | (u8x8_GetSPIClockPolarity( u8x8 ) << 1);
|
|
config.clock_speed_hz = u8x8->display_info->sck_clock_hz;
|
|
config.queue_size = 1;
|
|
|
|
spi_bus_add_device( hal->host, &config, &(hal->device) );
|
|
|
|
hal->last_dc = 0;
|
|
}
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_SET_DC:
|
|
if (hal->last_dc != arg_int)
|
|
flush_buffer_spi( hal );
|
|
|
|
u8x8_gpio_SetDC( u8x8, arg_int );
|
|
hal->last_dc = arg_int;
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_START_TRANSFER:
|
|
hal->buffer.size = 256;
|
|
if (!(hal->buffer.data = (uint8_t *)pvPortMallocCaps( hal->buffer.size, MALLOC_CAP_DMA )))
|
|
return 0;
|
|
hal->buffer.used = 0;
|
|
|
|
u8x8_gpio_SetCS( u8x8, u8x8->display_info->chip_enable_level );
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_SEND:
|
|
while (hal->buffer.size - hal->buffer.used < arg_int) {
|
|
hal->buffer.size *= 2;
|
|
uint8_t *tmp;
|
|
if (!(tmp = (uint8_t *)pvPortMallocCaps( hal->buffer.size, MALLOC_CAP_DMA ))) {
|
|
free( hal->buffer.data );
|
|
return 0;
|
|
}
|
|
memcpy( tmp, hal->buffer.data, hal->buffer.used );
|
|
free( hal->buffer.data );
|
|
hal->buffer.data = tmp;
|
|
}
|
|
memcpy( hal->buffer.data + hal->buffer.used, arg_ptr, arg_int );
|
|
hal->buffer.used += arg_int;
|
|
break;
|
|
|
|
case U8X8_MSG_BYTE_END_TRANSFER:
|
|
flush_buffer_spi( hal );
|
|
|
|
u8x8_gpio_SetCS( u8x8, u8x8->display_info->chip_disable_level );
|
|
|
|
if (hal->buffer.data)
|
|
free( hal->buffer.data );
|
|
break;
|
|
|
|
default:
|
|
return 0;
|
|
}
|
|
|
|
return 1;
|
|
}
|