nodemcu-firmware/docs/en/modules/enduser-setup.md

enduser setup Module

Since	Origin / Contributor	Maintainer	Source
2015-09-02	Robert Foss	Robert Foss	enduser_setup.c

This module provides a simple way of configuring ESP8266 chips without using a serial interface or pre-programming WiFi credentials onto the chip.

After running enduser_setup.start(), a wireless network named "SetupGadget_XXXXXX" will start (this prefix can be overridden in user_config.h by defining ENDUSER_SETUP_AP_SSID). Connect to that SSID and then navigate to the root of any website (e.g., http://example.com/ will work, but do not use .local domains because it will fail on iOS). A web page similar to the picture above will load, allowing the end user to provide their Wi-Fi information.

After an IP address has been successfully obtained, then this module will stop as if enduser_setup.stop() had been called. There is a 10-second delay before teardown to allow connected clients to obtain a last status message while the SoftAP is still active.

Alternative HTML can be served by placing a file called enduser_setup.html on the filesystem. Everything needed by the web page must be included in this one file. This file will be kept in RAM, so keep it as small as possible. The file can be gzip'd ahead of time to reduce the size (i.e., using gzip -n or zopfli), and when served, the End User Setup module will add the appropriate Content-Encoding header to the response.

Note: If gzipped, the file can also be named enduser_setup.html.gz for semantic purposes. Gzip encoding is determined by the file's contents, not the filename.

The following HTTP endpoints exist:

Endpoint	Description
/	Returns HTML for the web page. Will return the contents of enduser_setup.html if it exists on the filesystem, otherwise will return a page embedded into the firmware image.
/aplist	Forces the ESP8266 to perform a site survey across all channels, reporting access points that it can find. Return payload is a JSON array: [{"ssid":"foobar","rssi":-36,"chan":3}]
/generate_204	Returns a HTTP 204 status (expected by certain Android clients during Wi-Fi connectivity checks)
/status	Returns plaintext status description, used by the web page
/status.json	Returns a JSON payload containing the ESP8266's chip id in hexadecimal format and the status code: 0=Idle, 1=Connecting, 2=Wrong Password, 3=Network not Found, 4=Failed, 5=Success
/setwifi	Endpoint intended for services to use for setting the wifi credentials. Identical to /update except returns the same payload as /status.json instead of redirecting to /.
/update	Form submission target. Example: http://example.com/update?wifi_ssid=foobar&wifi_password=CorrectHorseBatteryStaple. Must be a GET request. Will redirect to / when complete.

enduser_setup.manual()

Controls whether manual AP configuration is used.

By default the enduser_setup module automatically configures an open access point when starting, and stops it when the device has been successfully joined to a WiFi network. If manual mode has been enabled, neither of this is done. The device must be manually configured for wifi.SOFTAP mode prior to calling enduser_setup.start(). Additionally, the portal is not stopped after the device has successfully joined to a WiFi network.

Syntax

enduser_setup.manual([on_off])

Parameters

• on_off a boolean value indicating whether to use manual mode; if not given, the function only returns the current setting.

Returns

The current setting, true if manual mode is enabled, false if it is not.

Example

wifi.setmode(wifi.STATIONAP)
wifi.ap.config({ssid="MyPersonalSSID", auth=wifi.OPEN})
enduser_setup.manual(true)
enduser_setup.start(
  function()
    print("Connected to wifi as:" .. wifi.sta.getip())
  end,
  function(err, str)
    print("enduser_setup: Err #" .. err .. ": " .. str)
  end
);

enduser_setup.start()

Starts the captive portal.

Note: Calling start() while EUS is already running is an error, and will result in stop() to be invoked to shut down EUS.

Syntax

enduser_setup.start([onConnected()], [onError(err_num, string)], [onDebug(string)])

Parameters

• onConnected() callback will be fired when an IP-address has been obtained, just before the enduser_setup module will terminate itself
• onError() callback will be fired if an error is encountered. err_num is a number describing the error, and string contains a description of the error.
• onDebug() callback is disabled by default (controlled by #define ENDUSER_SETUP_DEBUG_ENABLE in enduser_setup.c). It is intended to be used to find internal issues in the module. string contains a description of what is going on.

Returns

nil

Example

enduser_setup.start(
  function()
    print("Connected to wifi as:" .. wifi.sta.getip())
  end,
  function(err, str)
    print("enduser_setup: Err #" .. err .. ": " .. str)
  end,
  print -- Lua print function can serve as the debug callback
);

enduser_setup.stop()

Stops the captive portal.

Syntax

enduser_setup.stop()

Parameters

none

Returns

nil