01ca56fdce
Support all different section syntaxes (sx, sy, ...) side by side
2019-06-21 21:37:57 +02:00
db706fc939
SlatWall edges: Make bottom hook selectable, various fixes
2019-06-21 21:36:28 +02:00
1e35a3b9ed
New generator: SwSlottedHolder
...
A tool holder for slat wall
2019-06-21 21:22:10 +02:00
5cef906a9a
Add SlatWallHoleEdge (dD) classes
...
Similar to FigerHolesEdge (h)
2019-06-21 18:47:29 +02:00
9415a6864f
Add boxes/generators/_swtemplate.py as a starting point for Slat Wall boxes
2019-06-13 19:02:02 +02:00
aadf5ceafc
Add Edge types, example and UIGroup for slat wall compatible boxes
2019-06-13 19:00:32 +02:00
753422fa46
New generator DiscRack
...
A rack for storing disk-shaped objects vertically next to each other
2019-06-01 13:09:01 +02:00
e8e248994b
Add a StorageSelf generator. This is a shelf for storing TypeTray boxes.
...
It is based on TypeTray generator. The sh parameter replace the sx parameter.
It is not a subclasse of TypeTray in order to have the top and bottom at
the right place.
2019-06-01 12:52:34 +02:00
a6ca723759
Mirror holes on the other walls
...
to have them match up. Otherwise boxes with non symetric top edges don't fit
together.
Fixes #141
2019-05-11 17:18:10 +02:00
46157b2030
Add .mirrorX() and .mirrorY() wrappers
...
These are especially useful for warpping callbacks.
2019-05-11 17:17:11 +02:00
93c2093ef3
AllEdges: Fix spacing and add edegs around the corner
...
to make it more clear which direction the edges are pointing.
Related #132
2019-04-14 18:17:09 +02:00
f22be6f6d5
Fix polygonWalls for inner corners
2019-04-14 18:17:09 +02:00
0b781ce7ef
Add turtle param to polygonWall
...
to allow using it as turtle graphic command instead of a part
2019-04-14 18:17:09 +02:00
dc11929258
Fix _polygonWallExtend for corners with negative angles
2019-04-14 18:17:09 +02:00
95dba0dee7
box: raise NotImplementedError
...
NotImplemented is a sentinel for comparisons; encountering this as an
exception would result in a meta-error.
2019-04-10 17:56:12 +02:00
ce8576d39e
New generator: HeartBox
2019-03-24 21:52:26 +01:00
7aec26e893
New .polygonWall() part
...
Similar to .polyline() but with (f) edges on the outside
.polygonWalls draws the surrounding walls
2019-03-24 21:50:36 +01:00
4f4d947253
.corner(): Fix tabs for small arcs
2019-03-24 21:50:11 +01:00
f178215f20
.corner(): Also accept (angle, radius) tuples
2019-03-24 21:50:11 +01:00
c09ee50fbd
New generator: NotesHolder
2019-03-23 12:36:21 +01:00
8bacd1f766
UniversalBox: Fix missing lids for various top_edges
...
Call got refactored away
Resolves : #121
2019-02-27 22:58:05 +01:00
fb4791f803
Fix typo in help text for tabs
2019-02-26 00:02:30 +01:00
cbb000f12e
DoveTailJoint: remove no longer needed ctx.translate
2019-02-24 14:45:57 +01:00
abed8c06ac
FingerHoles: use .saved_context()
2019-02-24 14:42:48 +01:00
72617110cf
FingerHoleEdge: Use modern code and add tab support
2019-02-24 13:14:21 +01:00
eb5f3008da
RoundedTriangleEdge: Add tabs
2019-02-24 12:16:47 +01:00
8640514daf
Omit reference for svg_Ponoko format
2019-02-14 21:36:54 +01:00
8db3942757
UniversalBox: Fix positioning of lid parts
2019-02-14 21:32:27 +01:00
25ea02d317
Handle the drawing reaching into the negative x axis properly
2019-02-14 21:15:28 +01:00
c6e872a146
Add tabs to .parts
2019-02-14 17:34:22 +01:00
81708bbbca
.polyline: mention tabs feature in doc string
2019-02-14 17:32:59 +01:00
3a0e34eed8
Fix NutHole which broke after switching over to saved_context
2019-02-14 17:31:56 +01:00
679234afd3
Fix docstrings of .open() and .close() to match new use pattern
2019-02-13 09:04:57 +01:00
9b1ce265bf
Make docstrings ready for autodoc
2019-02-13 09:01:20 +01:00
e3ba617f22
Fix traceback for top_edge == "L"
...
No longer access the t1 edge type after changing it which may lead
to t1 being a char instead of a Edge instance
Thanks to michael (https://hackaday.io/hacker/381347-michael ) for
pointing this out!
2019-02-10 19:49:51 +01:00
0d07f48b7f
Remove .open() call from the .render() method
...
Having this call there was necessary in the past as the open() method would
need the canvas size as a parameter. This is now determined automatically
after rendering.
Still calling open() is deprecated but won't result in an error.
2019-02-08 17:43:15 +01:00
861c8451e2
Remove call to .close() from .render() method
...
There is really no need for all the generator to care
Still calling it is deprecated but won't result in an error
2019-02-08 17:32:04 +01:00
2ba6fa1bf3
Use .saved_context() instead of .ctx.save() and .restore()
2019-02-07 22:43:04 +01:00
1724f67bdf
Delete never to be finished printer generator
...
This should have become a 3D printer using strings in a delta configuration.
2019-02-07 22:43:04 +01:00
ded5addbe9
Remove no longer needed calls to ctx.stroke()
...
Boxes.move() take care of that nowadays
2019-02-07 22:43:04 +01:00
80ab24dceb
Fix format of doc strings
2019-02-07 17:42:41 +01:00
c5d434105b
Add svg_Ponoko output format
...
This is just regular SVG with Ponoko-specific line properties
Yes, the lines are too thin to be seen in a regular web browser.
Resolves : #112
2019-02-03 16:30:28 +01:00
abacdd486e
Implement proper color handling
...
Avoid accessing Boxes.ctx (the cairo context) all over the code.
Have named colors
2019-02-03 16:28:02 +01:00
c573914bcd
Add Boxes.saved_context() context manager
...
Avoid directly accessing Boxes.ctx (the cairo context) all over the place.
Also have a more modern API for returning to a previous spot.
2019-02-03 16:25:31 +01:00
acb457be2a
Add GPL copy right header
2019-02-02 18:05:04 +01:00
2e5a19a40f
Python 2 compat fix
2019-01-12 18:42:44 +01:00
6f4e94577b
New generator: RectangularWall
2019-01-12 15:28:17 +01:00
dac6b3ac3d
Fix Edge descriptions
...
Add descriptions for edges that don't have their own class
Make ChestHingeFront sub class of Edge as BaseEdge no longer draws anything
2019-01-12 15:28:17 +01:00
1739d11af5
Doc string for GearSettings
2019-01-12 15:28:17 +01:00
d0356a12a3
Add parameters to addTopEdgeSettings() for changed defaults
2019-01-12 00:07:37 +01:00
ba3cacbf93
RoundedTriangleEdge: Add outset setting
2019-01-12 00:07:22 +01:00
2747d9719a
Add RoundedTriangleEdge to top_edges
2019-01-12 00:00:55 +01:00
31fd0024ee
Add RoundedTriangleEdge t
...
Based on the Caddy generator by bobm123 in the PR #14
(https://github.com/florianfesti/boxes/pull/14 )
Edge will be added to the TypeTray generator to achieve similar results as Caddy
Co-authored-by: bobm123 <bobm123@gmail.com>
2019-01-11 23:56:28 +01:00
64fb498e6e
UniversalBox: Use a more robust way of placing the pieces
...
No longer rely on all side walls having the same height
2019-01-11 19:41:02 +01:00
97e7e3b68f
TypeTray: Swap vertical edge types to match the layout of the UniversalBox
2019-01-11 19:41:02 +01:00
5c70515f01
TypeTray: Add lids matching top_edge
2019-01-10 22:27:36 +01:00
371097aa89
PaintStorage: Make grip hole smaller and more rounded
...
Fixes #108
2019-01-10 22:09:45 +01:00
c0a782b745
TypeTray: Add support for all top_edges
2019-01-03 11:13:27 +01:00
c2615d4b38
TypeTray: rearrange parts
2018-12-27 17:19:10 +01:00
73050d4969
Make .continueDirection() more private
2018-12-22 17:23:33 +01:00
2df63b6ec8
ShutterBox: Add style with two rounded corners
...
Move generator to FlexBox category
2018-12-19 18:04:34 +01:00
879b3149bb
New generator: ShutterBox
...
A box with a rolling shutter made out of flex
2018-12-13 18:39:01 +01:00
4a79c37e71
CardBox: Add gripping ledge to the lid
2018-12-11 19:33:52 +01:00
4d2592fecf
Add e edge to bottom_edge selection
2018-12-08 18:22:13 +01:00
fd956d1f08
rectangularHole(): clamp corner radius to available space
2018-12-08 12:42:36 +01:00
8f03030c53
PaintStorage: Add carrying hole
2018-12-08 12:37:20 +01:00
925c6ce6dc
PaintStand: Fix previous change
2018-11-24 22:47:35 +01:00
17e4eb8563
PaintStorage: Fix heights
2018-11-15 22:10:19 +01:00
ed6855d79c
RoundedPlate: Call first callback only once
...
Remove left over call to .cc()
2018-11-09 21:01:00 +01:00
d85fa4e849
LaserClamp: Improve design
...
Extend bottom bracket and add hook
Use only one bottom bracket
Add finger ring to allow easier placement
Improve top hook
2018-11-05 22:08:23 +01:00
0f999a89ad
New generator: AllEdges showing all the standard edge types
2018-11-05 21:38:49 +01:00
b7bd6306d1
Fix division by zero in FlexEdge
2018-11-05 21:38:49 +01:00
fe89528e05
PaintStorage: Add support for hexagonal hole patterns
2018-10-29 18:16:16 +01:00
36077e6cb0
PaintStorage: Optimize part placement
2018-10-29 15:44:18 +01:00
c28541a977
Add a generator for paintstand
...
A simple stackable paintstand, very much inspired by:
https://www.youtube.com/watch?v=6HJarJg1npk
2018-10-29 15:11:35 +01:00
e95f36a18a
Parameterize Silverwarebox
...
Make the messurements selectable
2018-10-28 13:19:37 +01:00
80288079af
New generator: TwoPiece
...
Based on a generator with the same name by bobm123<bobm123@gmail.com>
2018-10-25 22:35:20 +02:00
5b93c1228d
CardBox: Add num param for the number of decks
2018-10-25 17:36:46 +02:00
5a13fbea8b
Add DisplayCase generator
2018-10-24 21:28:54 +02:00
2060293cf3
New generator: RoyalGame of Ur
2018-10-24 21:23:57 +02:00
397cc81690
FlexBox3: Use .move()
...
Use .edgeCorner() instead of own implementation
2018-10-19 22:12:13 +02:00
f7c2d91e42
FlexBox2: Make latchsize configurable
2018-10-19 21:46:30 +02:00
417a053ad3
FlexBox2: Use .move()
2018-10-19 21:45:26 +02:00
4d76457d3a
FlexBox: Make latchsize configurable
2018-10-19 21:35:11 +02:00
791ef0fdca
FlexBox: Use .move()
2018-10-19 21:33:52 +02:00
a9009732ac
FlexBox4: Make latchsize configurable
2018-10-19 19:20:23 +02:00
4ba18d87b7
FlexBox4: Modernize a bit and use .move()
2018-10-19 19:15:55 +02:00
a4b5af98e2
Add new "mirror" key word to the where parameter of Boxes.move()
2018-10-19 19:05:07 +02:00
c45b5cd30b
Add debug rectangle for move commands
2018-10-19 18:58:29 +02:00
1cf671ddd2
FlexBox4: Calculate length of flex after adjusting the radius
2018-10-19 10:02:16 +02:00
716fd389e3
Add a box for storage of playingcards
...
The box have place for two stacks of cards with a divider between.
It have a slide in lid.
2018-10-09 16:55:34 +02:00
14c6338713
New generator: LaserClamp
2018-10-06 22:55:46 +02:00
60cb0eed87
CabinetHinge: Add style param with new value outside
2018-10-04 22:18:07 +02:00
b07983582e
HingeBox: Add support for split lids
2018-09-30 15:31:16 +02:00
db16b16533
.rectangularWall(): Fix placement for hex holes enabled by holesMargin param
2018-09-13 09:23:56 +02:00
9ad64a1764
Boxes.buildArgParser: Update doc string
2018-09-10 10:00:02 +02:00
259834a983
ArgparseEdgeType: Add doc string
2018-09-10 10:00:02 +02:00
84df48ba1d
Add units (mm) to the tabs param description
2018-09-10 10:00:02 +02:00
84ce484f93
[doc] add hint to disable reference
2018-09-08 15:33:09 +02:00
b8ff1b8cf6
TrayLayout: Make parsing a bit more robust
...
Ignore white space at the end of lines with horizontal walls
2018-08-27 16:55:00 +02:00
b4a95aca15
TrayLayout: Fix burn correction for bottom plate
...
All edges were missing the burn correction outset (aka kerf).
2018-08-27 15:13:31 +02:00
fc127237fd
Fix placement of fingerHoles in CrossingFingerHoleEdge
...
which were too low by one burn
2018-08-27 15:12:17 +02:00
0e8a718a1b
Fix placement of debugging rectangel for FingerHoles
...
Not the outer border of the lines are exactly at the border of the matching
part
2018-08-27 15:10:50 +02:00
3767598d5d
Fix placement of rectangularHole() which was off by one burn
2018-08-27 15:09:17 +02:00
ec77d6aa22
Doc strings for Parts methods
2018-08-23 23:28:24 +02:00
897fc23029
Doc string for Boxes.flex2D()
2018-08-23 23:28:24 +02:00
6c43f4a382
Doc string for Boxes.TX()
2018-08-23 23:28:20 +02:00
a99094b8d7
Doc string for Boxes.partsMatrix()
2018-08-23 23:27:35 +02:00
d360703cba
TypeTray: Make bottom_edge parametric
...
This does not affect the inside walls
2018-08-16 20:49:12 +02:00
46175dde11
Fix url params for checkboxes when re-opening an input form
...
Thanks to Rotzbua for pointing the issue out!
2018-08-16 08:54:52 +02:00
8563818925
Hook: Boxify and parametrize generator
2018-08-14 14:01:59 +02:00
2831b41d21
Add wall hook generator
2018-08-14 11:55:31 +02:00
f83ca31a0a
RoundedBox: Add wallpieces param
2018-08-06 19:46:48 +02:00
af7f29c51f
Add (wall)pieces param to roundedPlate() and surroundingWall()
2018-08-06 19:46:23 +02:00
7c8ae621f7
CloseBox: Put bed blots at the right places
...
Keep them still disabled, though.
2018-07-25 16:34:58 +02:00
05c41be4d1
Remove or comment debugging outputs
2018-07-24 20:36:13 +02:00
cd0fcdcb96
Set a char for CrossingFingerHoleEdge tp avoid collision with the "e" edge.
2018-07-02 19:13:52 +02:00
44bce898e0
UniversalBox: Add alternative "lid" for f and F top_edges:
...
A rim leaving the box open
2018-07-02 19:07:26 +02:00
2c7f9f4dc0
UniversalBox: Add f and F as possible top_edge types
2018-07-02 19:07:26 +02:00
37a798e91e
Add top "lid" for F edge
2018-07-02 19:07:25 +02:00
8b172cbddd
Add 10" rack box derived from 19" rack box
2018-06-27 21:48:35 +02:00
d75ea78196
Add support for specifying font color/size
2018-06-27 21:48:35 +02:00
6538c92910
OrganPipe: Offer multiple units for the pressure given
2018-05-18 14:12:30 +02:00
924372f79d
Use a minimal line width (0.05mm) even for very small burn values
...
to keep the lines visible in these cases.
2018-05-17 11:27:58 +02:00
1d0aa05e9a
OrganPipe: Use unicode for Py 2 compat
2018-05-12 17:14:02 +02:00
d9e8930e31
OrganPipe: Add encoding
2018-05-12 17:11:26 +02:00
4798c24815
New generator: Organ pipe
...
Still untested
2018-05-12 17:06:10 +02:00
f99bf32c85
Add hinges and spacing params to CabinetHingeEdge
2018-05-08 23:55:09 +02:00
2828a85725
Add flatHole() for shafts that are flattened on both sides.
2018-05-05 19:08:37 +02:00
50b9bc9ffb
TypeTray: Fix finger holes in bottom which had been mirrored in x direction
2018-04-25 23:36:32 +02:00
616bf42239
RegularBox: Fix top edge for "angled hole" top
2018-04-25 22:02:52 +02:00
d3c922d289
RegularBox: Use FingerJointSettings for vertical edges, too
...
Fixes #65
2018-04-25 22:02:24 +02:00
73438fb614
Fix .__getattr__ of Settings class so it can be passed to copy.copy()
2018-04-25 21:52:51 +02:00
879ae1af68
DisplayShelf: Do not render front wall if set to zero
2018-04-15 19:43:31 +02:00
ebe02e2be5
DisplayShelf: Use better defaults
2018-04-15 19:43:31 +02:00
65358c9fad
Add hint to outside param to nominally inner sizes
2018-04-05 22:55:23 +02:00
b2c54310b6
UnevenHeightBox: Fix lid
...
Looks like it is difficult to come up with a really non symmectrical test case.
Thanks to Mekol for pointing this out!
Related #60
2018-03-17 21:04:24 +01:00
fa44eb27cf
UneveHeigthBox: Minor tweaks
2018-03-17 17:32:21 +01:00
58cb06ec94
UnevenHeightBox: Add lid
2018-03-17 17:19:47 +01:00
7c716a9e5f
UnevenHeightBox: Make bottom edge parametric
2018-03-15 20:46:00 +01:00
786ff222c2
New generator: UnevenHeightBox
...
Box with different height in each corner
2018-03-15 19:08:47 +01:00
0604744284
OttoSoles: Add dove tail joints to the connecting edges
2018-03-11 17:43:55 +01:00
f2106a2c8c
OttoSoles: Add support for tabs
2018-03-11 09:13:40 +01:00
49ce2ed412
New generator: Ottosoles
...
Foam soles for the OttO Bot
2018-03-10 19:28:30 +01:00
90ba9f8ee9
LidEdge: Fix duplicated option for spring
2018-03-05 20:10:55 +01:00
dd7d282c65
Rack19Box: Fix width and placement of holes
2018-02-27 18:41:39 +01:00
66c419ab7f
New generator: Rack19Box
...
Closed box with screw on top for mounting in a 19" rack.
2018-02-27 18:04:26 +01:00
c3917d3292
IntegratedHingeBox: switch x and y measurements
...
So the hinge is at the backside along the x axis
2018-02-20 08:23:07 +01:00
8cb9919968
FlexBox2: Rename params to reflect the actual axis of measurement
...
h -> x
y -> h
x -> y
2018-02-19 16:49:04 +01:00
78d35a92e0
Fix CrossingFingerHoleEdge
...
which relies on __call__() of the super class drawing a line
2018-02-12 22:04:20 +01:00
211e302b41
Fix devision by zero for zero lengths
2018-02-10 21:00:08 +01:00
039fe5f2ee
ElectronicsBox: Fix holes in the lid
2018-02-03 22:33:27 +01:00
a70222d646
New generator: RackBox
2018-02-03 22:31:53 +01:00
6ef43a8f48
Add flangedWall() and use it in the ElectronicsBox
2018-02-03 21:52:12 +01:00
b0bef745b2
ElectronicsBox: Fix top edge and height
2018-02-02 14:06:18 +01:00
a53c5857c2
New generator: AngledCutJig
...
For making angled cuts in a laser cutter
2018-01-21 22:05:48 +01:00
8314a413fd
Fix placement of rectangularTriangles
2018-01-21 16:48:43 +01:00
4e034949d3
Fix tabs for straight edges (eE) with bed bolts
...
Add tabs param to bedBoltHole
2018-01-19 23:48:27 +01:00
73e1821e71
enable bedbolts for Straight 'e' and OutSet edges 'E'
...
note that this mostly ignores that positioning bedbolts is done
in the BedBolt class for finger joints.
Coding style could be much improved.
2018-01-18 15:07:33 +01:00
07f88cd8e5
make __call__() abstract for BaseEdge; and inherit OutSetEdge from Edge
2018-01-18 15:07:24 +01:00
62b6016448
OttoLegs: Increase number of tabs for feet and ankles
2018-01-13 21:11:33 +01:00
68f1c375f7
OttoLegs: Move tabs to outer ring
2017-12-20 18:25:55 +01:00
7bd2b9e452
HingeEdge: Add tabs to hinge disk
2017-12-20 18:25:55 +01:00
ce240105a8
Add tabs param to hole()
2017-12-20 18:25:55 +01:00
c02cc1e95c
Add tabs to corner
2017-12-20 18:25:55 +01:00
d2496df3bb
Boxes.moveArc()
2017-12-20 18:25:44 +01:00
703d0e49db
OttoBody: Add tabs to the PCB clamps
2017-12-19 20:10:08 +01:00
f44f87a25c
Remove print for Python 2 compat
2017-12-19 19:36:37 +01:00
946d040bac
OttoBot: Move to Misc UI Group
...
Set default leg legth to 34mm
2017-12-18 23:49:18 +01:00
e26991695a
Mark top side of servo mount.
...
Move servo mounts up as they need to be cut separately (in 5mm)
2017-12-17 15:30:32 +01:00
e5bb6a5d7a
Add tabs to Boxes.edge() and most Edge classes
...
and Boxes.polyline()
Add to some parts of the Otto Bot
2017-12-15 16:45:32 +01:00
e0caa3aad8
OttoBody: Add fix for changed ChestHinge
2017-12-09 16:54:20 +01:00
f0dc89c617
Make play of ChestHinge a regular param
2017-12-09 16:54:10 +01:00
9dfa95f45b
Fix ChestHinge
...
Add the play of the hinge to the width of the edge
Adjust IntegratedHingeBox
Fixes #45
2017-12-07 22:29:09 +01:00
319b1f869f
Use unicode for Python 2 compat
2017-11-30 23:32:30 +01:00
d52b561a2f
Use explicit encoding
2017-11-30 23:30:50 +01:00
1b2f5791bd
Use Boxes.description in the cli help and the web interface
2017-11-30 22:48:02 +01:00
3dfd99c68a
Rename method to not collide with new description property
2017-11-30 22:46:35 +01:00
72e6dd2213
Added a description to TrafficLight generator
2017-11-30 22:46:35 +01:00
fa9ac678c0
Added variables for description of generators to main class
2017-11-30 22:46:35 +01:00
0d9885ad4c
Stachel: Fix length of pin clamp for middle layer
2017-11-23 21:04:54 +01:00
2772eba87c
Gears: holes for the shafts
2017-11-22 21:32:25 +01:00
a7f6ef1b62
Gears: Print sizes
2017-11-22 21:32:04 +01:00
afbb8d11fd
Gear generator
2017-11-22 21:32:04 +01:00
eb07c927c4
Support multi line .text()
2017-11-22 21:32:04 +01:00
f77c19d839
Stachel: Clean up and move generator to Misc
2017-11-21 23:08:39 +01:00
5a6bc71a7c
Stachel: replace absolute sizes with (internal) parameters
2017-11-21 22:39:57 +01:00
941676d2b7
New generator: Stachel - an end pin for bass recorders
2017-11-21 22:39:57 +01:00
08d7a026b1
NemaMount: Add finger holes to copy on another part
...
instead of using the base plate
2017-11-19 19:30:06 +01:00
642212d2ce
New generator: NemaMount
2017-11-19 18:10:59 +01:00
46c4960edc
New generator: Display
2017-11-18 18:28:13 +01:00
45c73e57fb
New generator: EletronicsBox
...
Closed box with screw on top and mounting holes
2017-11-15 17:19:41 +01:00
90078049f8
Also support d (diameter) param for Boxes.hole()
2017-11-15 17:19:41 +01:00
36c0ec48fe
TypeTray: Add closedtop parameter
...
Add a top wall turning the type tray into a closed box with multiple
compartments
2017-11-14 20:21:01 +01:00
7793729688
New generator:LBeam
...
Simple Lbeam made of two wall joint with a right angle
2017-11-14 20:20:08 +01:00
8d846df9d1
Add D holes to knobs
2017-11-07 23:39:50 +01:00
c0325b52ac
template: Remove invalid parameter and whitespace
2017-11-03 22:54:06 +01:00
dd2cedeb57
Knobs: Improve param descriptions
2017-10-01 21:13:29 +02:00
696307397d
Refuse knobs with less than 2 serrations
2017-10-01 21:01:18 +02:00
98e9f827ec
waivyKnob: Fix number of serrations
...
Used to print only have the number of serrations and didn't close
on uneven numbers
2017-10-01 20:54:04 +02:00
dfcf3d65c8
New generator: ConcaveKnob in Parts
2017-10-01 20:34:19 +02:00
647c5302b6
New generator: WaivyKnob
2017-10-01 20:20:36 +02:00
241c65b244
.waivyKnob(): Fix start position for angles != 45 degees
2017-10-01 20:18:42 +02:00
64c980817b
Manully select font face
2017-09-19 22:53:27 +02:00
9dbc8fd98b
Modernize _template.py
2017-09-16 21:30:41 +02:00
f829ff2a82
PoleHook: Use screwhead param for knob
2017-09-16 21:30:41 +02:00
b7f877eacd
Fix bedbolts
...
BedBoltSettings need to become a subclass of Settings instead of a list
of values at some point.
2017-09-13 11:39:03 +02:00
b623008ea3
ClosedBox: fix (commented out) BedBolt support
2017-09-13 11:39:03 +02:00
23a1da105e
WineRack: Remove debug code for checking number of walls needed.
2017-09-05 23:05:11 +02:00
7453455512
WineRack: Make unnecessary walls optional
2017-09-05 23:00:54 +02:00
0e7827f9a9
WineRack: Add front cover
2017-09-05 21:04:20 +02:00
fbfb851474
New generator: WineRack
...
A honey comb like wine rack
2017-09-05 21:04:20 +02:00
ab750077fa
.partsMatrix(): Do not error out for zero or negative parts count
2017-08-28 23:10:56 +02:00
ddcf13bf6c
svgutil: Make detection of view port a bit more robust
2017-08-20 19:56:33 +02:00
592fbe95c4
OttoLegs: Change ankles. Fix servo horn with a C-ring
...
Fixes issue with servo horns only being adjustable in steps of 18 degrees
This led to missaligned feet which resulted in loss of freedom of movement.
2017-08-19 22:14:30 +02:00
6fecb9aa29
OttoBody: Move main switch to outer wall
...
Shorten servo holder so it no longer needs a hole for the switch
2017-08-19 19:31:54 +02:00
398851255d
OttoLegs: Use servo horn for actuating the ankles
2017-08-12 00:07:34 +02:00
4dd271df74
OttoLegs: Make ankle screw screwed into leg
...
to give more stability to the joint
2017-08-11 18:44:34 +02:00
bb76a8bd7b
OttoLeg: Use partsMatrix to get multiple part
2017-08-11 17:46:50 +02:00
93b94d6e70
Fix move="right" for partsMatrix
2017-08-07 17:08:16 +02:00
09dd779cbd
OttLegs: Make hole for servo cable over whole width of the leg
2017-08-07 17:03:57 +02:00
fafc1c01ef
OttoLegs: break ankles into separate paths
2017-08-03 23:19:32 +02:00
e91f53b0fa
OttoLegs: Change design of ankles
2017-08-03 23:00:20 +02:00
b4b6799721
OttoBody: Add hook to PCB Clip
2017-08-03 22:32:33 +02:00
e3035da713
OttoBody: Move hole for push button
2017-08-01 21:19:01 +02:00
2e9ac29d01
OttoLegs: Make length of legs configurable
2017-08-01 21:17:35 +02:00
979b6ae936
OttoBody: Add push button
2017-07-31 21:18:06 +02:00
a639c04de2
OttoBody: Clips for keeping the mouth shut
2017-07-31 21:08:26 +02:00
31e3817f32
OttoBody: New PCB Clamps
2017-07-31 20:46:41 +02:00
fd23c74e07
Otto Body: parts for mounting the PCB
2017-07-30 21:23:00 +02:00
e26d17c840
AngledBox: Don't overwrite h param
...
Using h as temporary variable was overwriting the variable containing the
height of the box.
Fixes #41
2017-07-28 23:33:36 +02:00
83a72552e2
Ottobot: Make hole for USB plug a bit smaller again
2017-07-25 22:43:11 +02:00
c823cb78d6
OttoBot: Add Hole for on/off switch
2017-07-25 21:57:58 +02:00
3876ea5ddd
Ottobot: Increase hole for USB plug
2017-07-23 21:29:14 +02:00
074646fdec
_template.py tweaks
2017-05-20 20:41:51 +02:00
82463317bb
Edges generator for printing the registerd Edge types
...
Not really a generator...
2017-05-20 20:41:51 +02:00
abb7706b6d
Python2 compat for Inkscape
2017-05-14 21:47:49 +02:00
770b3dc02f
Add .dHole()
2017-05-05 16:52:42 +02:00
d7aadc9b72
Add callback param to gears.gearCarrier()
2017-05-04 21:41:18 +02:00
07ede0a5c5
Add support for "only" in the move param of .partsMatrix()
2017-05-04 21:41:18 +02:00
9bf9922d28
Stroke in move after part is completed
2017-05-04 21:41:18 +02:00
3822cc4882
Add TX holes
2017-05-04 21:41:18 +02:00
ae619aabea
Flexbox4: Fix length of lid
...
to overlap the side wall
2017-04-11 21:09:41 +02:00
7bbf82c958
UBox: Fix size of lid
2017-04-11 20:55:21 +02:00
b63dcfeee6
Make Traylayout work without main function
2017-04-05 04:33:42 +02:00
5b9c8e4d71
Remove main function from generators
...
Generators are no longer executable on their own. Use scripts/boxes
instead.
2017-04-05 04:33:42 +02:00
bffd732c3f
scripts/boxes: Use generator classes instead of main functions
...
Make Boxes.parseArgs more robust
--list generators by UI group.
Pass arguments explicitly instead of fiddling with sys.argv
2017-04-05 04:33:28 +02:00
f9c0cb8cab
Support putting class and instances into UI Groups
2017-04-02 02:31:37 +02:00
8e65298c6b
Planetary2: Print gearing ratio and change default for sun gear
2017-04-01 23:54:44 +02:00
12f2cbc1e2
Planetary2: Add allignment pins to sun gear
2017-04-01 21:18:48 +02:00
273190932f
Planetary2: Order part the way they need to go together
2017-04-01 21:06:57 +02:00
4c17d6a4a1
Planetary2: Put planet gears in the order they need to go together
2017-04-01 20:59:19 +02:00
7f1e54be15
Planetary2: Add pin holes for ring gear and add second ring
2017-03-30 20:59:13 +02:00
8487d5c379
Planetary2: New generator for a ~100 reduction to belt pulley
2017-03-29 07:44:48 +02:00
93480e082d
gears: Add teeth_only param to allow using gears as lines and not only as parts
2017-03-29 07:42:57 +02:00
427a6fc54b
Change default of mount_hole to 0
2017-03-29 07:42:15 +02:00
bad114400f
Use better default for height of pulley (using the new keyword style)
2017-03-29 07:41:05 +02:00
ff6da9eb80
Fix pulley size calculation for r_axle being None
2017-03-29 07:40:17 +02:00
c7490155f7
Add nema_mount default parameter
...
Make nema_sizes available outside of NEMA() function.
This whole stuff should probably move into it's own file/class at some point
2017-03-29 07:38:10 +02:00
53cbed768b
Allow using keyword args for buildArgParser for setting the defaults
2017-03-29 07:36:50 +02:00
c2fa8c85cf
Pulley: Add insideout param
...
This allows using timing belts as strainwaves in harmonic drives.
2017-03-22 22:03:09 +01:00
c2ab70eefe
Add Boxes.circle() primitive
2017-03-22 22:03:09 +01:00
71bd013f3f
RegularBox: Better description
2017-03-13 11:41:12 +01:00
cd0d49bf6f
OttoLegs: Use two different hole sizes for the ankle
...
to allow screwing it into one side while moving freely on the other
2017-03-12 14:47:21 +01:00
cd3fee5e76
OttoLegs: More tweaks
...
Lengthen front by 1mm to close gap to servo
Lower ankle hole at leg by 0.5mm
Shorten internal wall holding the servo at top
2017-03-11 20:14:29 +01:00
672295310b
OttoBody: Body for Otto LC
2017-03-11 18:22:41 +01:00
c6c2e203f2
OttoLegs: Make ankle bolt diameter configurable
2017-03-11 18:22:41 +01:00
271bed0308
OttoLegs: wall for better fixating the servos
2017-03-11 18:22:41 +01:00
6bc695a418
OttoLegs: Add second leg
2017-03-11 18:22:41 +01:00
e316877d06
OttoLegs: Make room for cables
2017-03-11 18:22:41 +01:00
db4e878bb4
OttoLegs: Legs for Otto LC
2017-03-11 18:22:41 +01:00
121e2107fb
Import lxml locally to avoid hard dependency
...
The code is used in the Inkscape plugin only.
2017-03-10 23:00:41 +01:00
4ab1dcc323
RoundedBox: Fix description
2017-03-06 22:24:05 +01:00
eecbceda11
Rename Box2 -> UniversalBox
2017-03-06 22:24:05 +01:00
47f3037e23
rename Box3 -> OpenBox
2017-03-06 22:24:05 +01:00
5026c2bc03
Rename Box5 -> HingeBox
2017-03-06 22:24:05 +01:00
e5b19978dd
Rename Box4 -> IntegratedHingeBox
2017-03-06 22:24:05 +01:00
75b7724255
Rename Box -> ClosedBox
2017-03-06 22:24:05 +01:00
5956182328
Parts.ringSegment()
2017-03-05 12:52:44 +01:00
5e33d057fc
UBox: Limit radius to possible values and merge flex if radii touch
2017-03-04 15:29:28 +01:00
a0d992f43a
Stop printing random stuff on stdout
2017-02-26 17:02:16 +01:00
41bc4d028f
Use sys.stdout.buffer to be able to write bytes (for Python 3 compat)
2017-02-25 19:59:53 +01:00
cb8ebefeb1
Fix Servo.choices() and use it in robotarm
2017-02-25 19:59:16 +01:00
174b20fc11
Fix main
2017-02-25 19:40:24 +01:00
a81ba48d45
Take viewBox and size of SVG documents into account when merging them
2017-02-25 16:10:28 +01:00
ce87babfdd
RoundedBox: Fix hole size
...
Size calculation was wrong but compensated the broken size adjustment with
"outside" set.
2017-02-25 15:52:51 +01:00
490d089a83
Planetary: Python2 fix. // doesn't allow floats in Python 2
2017-02-25 11:24:58 +01:00
d4edafe2d9
Fix ChestHingeSetting
...
Got broken by 6756d16b67
2017-02-23 20:57:01 +01:00
e0a4d06c43
Hackish way to make scriptsboxes to work with Inkscape.
2017-02-23 17:38:26 +01:00
ff7ee22885
Add svgutil.svgMerge() allwing to add generated box into anoterh svg
...
Implemetation has still many short comings. E.g. assumes units and layout of
document passed in. Also assumes to be merged document to be generated by
boxes.py.
2017-02-23 17:38:26 +01:00
39e74e67ba
Add scripts/boxes2inkscape for generating inx files from box generators
...
Code for handling traylayout still missing.
2017-02-23 17:38:26 +01:00
a93e280477
Make reference a separate path object
...
Avoid it being merged with teh first par tof the drawing
2017-02-23 17:38:26 +01:00
e23d8034c5
Make BoolArg accept upper and lower case values
2017-02-23 17:38:26 +01:00
b440d1c767
Use BoolArg when creating arg parser for edges.Settings
2017-02-23 17:38:26 +01:00
1b3f9dbc3a
Robotarm: Generator for servo powered robot arm segments
2017-02-22 22:33:22 +01:00
40d53ac1ba
Robot parts: Initial commit
2017-02-22 22:33:22 +01:00
1bed3f2a39
rectangularWall() fix positioning with ignore_widths
...
containing parts of the lower left corner.
2017-02-22 20:01:29 +01:00
3cad4f27af
Add tangent() function
2017-02-22 20:01:28 +01:00
d2774f151d
Lamp: fix no longer valid default in setting
2017-02-18 19:13:57 +01:00
cc577956a4
Flexbox3: Fix radius of lid
...
May still be off a bit. But I can't see why...
2017-02-18 19:06:10 +01:00
117ace3233
FlexBox3: Fix finger joints of lid
2017-02-18 19:06:10 +01:00
1f9342b678
Castle: Make available in UI and adjust to current code base
2017-02-18 19:06:10 +01:00
6756d16b67
Use .settings.thickness in edges instead of global value
2017-02-18 19:05:21 +01:00
561eb0034c
Add "Unstable" UIGroup
2017-02-15 15:55:01 +01:00
d3c76f2b9e
Put box generator into groups and adjust the menu web page accordingly
2017-02-13 17:31:58 +01:00
5a0f3d42ea
Add UIGroup class and instances for structuring the box generators
2017-02-13 17:31:02 +01:00
c820c1b77d
Move lid code from boxes/generators/box2.py to boxes/lids.py
...
Rename the classes to no longer show up in the list of generators
2017-02-12 23:18:37 +01:00
0739fd0b94
Exclude Boxes classes starting with _ in getAllBoxGenerators()
...
Exclude mix-in classes that are not supposed to be used on their own
2017-02-12 22:20:32 +01:00
399e5b468f
New generator: UBox - a box with rounded corner at the bottom
2017-02-12 15:00:17 +01:00
b59de950c0
Box2: Refactor lid generation out of the Box2 class
2017-02-12 15:00:17 +01:00
dd6c5560f9
Support chars es edge parameters in Boxes.edgeCorner()
2017-02-12 15:00:17 +01:00
a7d0dda9f8
New generator: Box5 box with lid attached with cabinet hinges
2017-02-11 18:15:44 +01:00
305986dad8
Add cabinet hinge to top_edge and support it in Box2
2017-02-11 18:15:44 +01:00
94c727cc30
Add CabinetHingeEdge
2017-02-11 18:15:44 +01:00
fb5398b30d
PoleHook: Initial commit
2017-02-11 18:15:34 +01:00
f1b8d68d65
Fix bedbolts for finger holes
2017-02-11 18:15:34 +01:00
250131e152
Fix previous fix *sigh*
2017-02-09 18:47:20 +01:00
3e3ed3b0dd
Add finger joint settings again
...
Got removed accidentially in 8d754c
2017-02-09 00:02:41 +01:00
da6dcb4c68
Box4: Use ignore_widths to get finger joints on the whole length of all edges
2017-02-07 20:18:48 +01:00
3daa9a846a
Add ignore_widths param for rectangularWall()
...
It does not pass the width of edges to edgeCorner but instead lengthen the
neighboring edge. The widths are numbered from 0 to 7 starting with the
horizontal part of the lower right corner.
2017-02-07 18:56:07 +01:00
1e6893d0b1
Box4: Box with boxy lid and built-in hinge
2017-02-06 22:36:11 +01:00
544c40a0d3
Add Chest Hinge edge classes
2017-02-06 22:35:26 +01:00
70574056d6
Fixes for rectangularTriangle
2017-02-05 21:02:46 +01:00
2fa07190ff
Fix finger joint setting defaults
...
space and width got mixed up in 8d754c3855
2017-02-05 16:30:37 +01:00
f982918205
Add r param to rectangularTriangle()
2017-02-04 15:01:16 +01:00
07661b1eae
Formats: Generate tempfile in same directory to ensure rename works.
2017-02-04 15:01:16 +01:00
8d754c3855
Use default finger/width settings of 2.0 for every box
2017-01-30 10:12:27 +01:00
c36d819e10
Change defaults
2017-01-30 09:37:10 +01:00
17e2b55fcf
Box2: Add flat lid
...
Make chestlid param a general lid param
2017-01-24 22:49:25 +01:00
28ad1c6dc3
RoundedBox: Add top param for top opening and lid
2017-01-21 13:54:58 +01:00
6ef950816e
Add edge parameter to Boxes.roundedPlate
2017-01-21 13:54:58 +01:00
a8241b2118
New generator: RoundedBox
...
Still very basic. Needs top parameter similar to AngledBox
2017-01-19 21:36:43 +01:00
fa4fd943ca
New generator: DisplayShelf - a shelf with forward slanted floors
2017-01-14 23:13:22 +01:00
8514ede2c3
AngledBox: Fix fingers on top of walls for "angled hole"
2017-01-08 18:56:05 +01:00
7b5614659a
New generator: AngledBox
2017-01-08 17:25:36 +01:00
8dc13440ee
Fix boolean params. Not passing 0, None, False or off works for setting them to False
...
Thanks to chrisjshull for pointing out how to fix this in the web UI.
Fixes #19
2017-01-08 17:25:36 +01:00
13cdb35954
Make RegularPolygonWall a path of its own
2016-12-17 11:37:11 +01:00
0cbd713718
RegularBox: Fix outside parameter
2016-12-17 11:36:26 +01:00
0dc6aef5d4
RegularBox: Add angled hole top style
2016-12-17 11:24:47 +01:00
b2b0ccd6f1
Fix FingerJoints with angles != 90 degrees
...
Fix margins
Fix amount of recess for spaces
2016-12-14 22:07:36 +01:00
6298c80527
RegularBox: Fix angled lid
2016-12-14 21:02:49 +01:00
a5fd1775e0
New generator: RegularBox
2016-12-13 22:58:56 +01:00
cbe32cc5a7
Code for Regular Polygons
...
* Boxes.regularPolygon for calculation
* Boxes.regularPolygonAt for simple polygon
* Boxes.regularPolygonWall
Also fix edgeCorner() for angles != 90 degrees
2016-12-13 22:58:10 +01:00
75adf0b15f
TrafficLight: Add support for horizontal layout of lights
2016-11-30 21:45:17 +01:00
f133e2aa12
TrafficLight: Add windows to be cut from transparent (and colored) material
2016-11-30 18:31:44 +01:00
16e93ca086
TrafficLight: Fix edge type for front panels
2016-11-30 11:29:55 +01:00
23cf0eaa3a
TrafficLight: Add param for number of lights
2016-11-29 23:43:01 +01:00
273174fae8
New generator: TrafficLight
2016-11-29 23:42:17 +01:00
aa4c0fd1d4
Add FingerJoints to the bottom of the front plates
2016-11-28 21:11:38 +01:00
be6de6a793
Support FingerJoints with less than 90 degrees.
...
This means bending angle < 90. The actual angle is bigger than 90
2016-11-28 21:11:38 +01:00
6f0a4cae86
Use polyline() for FingerJointEdge
2016-11-28 21:11:38 +01:00
aa5fa73c8a
Add edgeObjects() method to Settings to create Edge objects
2016-11-28 21:11:38 +01:00
f30221d265
Fix .margin() for CompondEdge
2016-11-26 13:40:27 +01:00
a0be85764a
Use FingerJointSettings.height as margin of Finger Joints
2016-11-17 21:39:32 +01:00
0fc6527150
BinTray: Switch slots between vertical and horizontal walls
...
to better support the floors.
Also fix margin of BinFront edge class(es)
2016-11-13 11:58:07 +01:00
c39b33ad14
New BinTray generator
2016-11-13 00:40:55 +01:00
69ac52aaab
Slide-on Edge: Add optional springs that hold the lid in place
...
Fix pin length to two thicknesses
2016-11-12 17:50:29 +01:00
43c0178d14
Make fingers for slide-on lid bigger by defaut
2016-11-12 17:01:44 +01:00
a8af428941
Manually use multiple arcs to get more precise curves
2016-11-02 21:50:44 +01:00
fe79970cc3
Beautify web UI
...
Watch self.css
2016-11-01 23:46:25 +01:00
0cde4a71e6
Add params for edge settings to all generators
2016-11-01 23:46:25 +01:00
7baafebaea
Remove debug print
2016-11-01 23:46:25 +01:00
748d8b3888
Remove arguments for FingerJoints from default arguments
2016-11-01 23:46:25 +01:00
ec2a365598
Use arguments from default Setting classes when creating the default edges
2016-11-01 23:46:25 +01:00
d980c6b95f
Add minimal doc strings to Settings
2016-11-01 23:46:25 +01:00
c3e2470e8d
Rename style values to something more meaningful
2016-11-01 23:46:25 +01:00
2ace15475a
Check types in Settings class and support choices
2016-11-01 23:46:25 +01:00
699fb920bc
Make Hinges more robut against invalid style arguments
2016-11-01 14:04:35 +01:00
fd3a333cb0
Allow passing new default values to Boxes.addSettingsArgs()
2016-11-01 14:04:35 +01:00
c816de811b
Beautify doc strings of edge settings and sort argument entries
2016-10-31 22:16:51 +01:00
3a0df10866
Create arguments from edge settings starting with FingerJointSettings
2016-10-31 22:13:09 +01:00
5a721df82b
Put arguments into groups and use them to display them in the web interface
2016-10-31 22:11:54 +01:00
9095c3934f
Return to original point after drawing finger holes
2016-10-30 20:20:56 +01:00
44b55029a0
Do not break lines on empty callbacks
...
Boxes.cc() did move the coordinate system arround even if the callback is
None. This breaks the continuity of the border. If there is callback the
line is still broken.
2016-10-30 20:20:56 +01:00
33d11487de
Add edges for a sliding lid
...
Add to top_edges and support in Box2
2016-10-30 20:17:13 +01:00
2494aeb3ae
Add play param for FingerJoints
2016-10-30 19:48:59 +01:00
7203320e70
Move finger calculation into FingerJointBase class
2016-10-30 19:48:59 +01:00
dc045eefe2
Remove no longer needed local vars
2016-10-30 19:48:59 +01:00
9220bccb68
Clarify burn param
2016-10-20 20:07:23 +02:00
4e632325e3
Arcade: Increase height of keyboard
2016-10-17 21:29:58 +02:00
9b4a45a1d5
Arcade: Add width as a parameter
...
Fix movement of side
2016-10-17 21:16:02 +02:00
ff6ba3595d
New Generator: Arcade - a desktop arcade cabinet
2016-10-17 21:12:12 +02:00
4f3883374d
Fix position of finger holes
2016-10-15 20:57:36 +02:00
24a8588485
gears.py: allow zero spokes
2016-10-12 22:52:35 +02:00
3ce2115365
Add RackEdge
2016-10-12 22:52:35 +02:00
fc36515fbd
Properly center rack and make it a single line for negative base heights
...
Preparation for RackEdge
2016-10-12 22:52:35 +02:00
accb6eb45d
gears.py: Support non closed line segments in drawPoints()
2016-10-12 22:52:35 +02:00
33681db645
Add closed param to kerf()
...
Allow for non close line segments and handle ends correctly
2016-10-12 22:52:35 +02:00
de7a168377
vectors.py: Don't error out when normalizing zero length vectors
2016-10-12 22:52:34 +02:00
83f0c813dd
vectors.py: add circlepoint(r, a)
2016-10-02 20:48:22 +02:00
ad00d64b26
partsMatrix()
2016-10-02 20:48:22 +02:00
586aeb7fb3
Allow finger joints as top edge
...
Add matching lid to Box2
2016-10-02 20:47:02 +02:00
0764a3660f
gears.p: More fixes for racks
2016-10-01 23:30:32 +02:00
bc1d9ce19e
gears.py: fix rack with draw_guides=False
2016-10-01 22:35:32 +02:00
b0fb04762b
Rotary: Make beam dimmensions parametric
2016-09-28 17:56:42 +02:00
610a26736e
Support drawing multiple rectangularTriangle(s) at once
...
Add support for setting diagonal edge type
2016-09-26 21:59:52 +02:00
cc42a8e165
Add rectangularTriangle()
2016-09-26 21:59:52 +02:00
14acd07faf
Fix latch length
...
Remove no longer needed burn correction
2016-09-26 21:59:52 +02:00
09ce2bd78b
Fix size virtual size of gear carrier
2016-09-26 21:59:52 +02:00
46f40bdae6
Planetary: Fix description
2016-08-22 20:48:21 +02:00
93af56ff9c
Code Reformat #1
2016-08-17 15:07:41 +02:00
af167295b8
Rotary: Fix spindle mechanism. Increase width of scissor lift to 70mm.
2016-08-05 22:59:35 +02:00
828cd12d49
Rotary: Add knifethickness param and support variant for honey comb table
2016-08-05 22:59:35 +02:00
072845be57
Rotary: Make some clearing space over the idle rollers
2016-08-05 22:59:22 +02:00
77e39669e8
Rotary attachment for laser cutter - first steps
2016-08-05 22:58:39 +02:00
36d6cd77c3
Fractal jigsaw puzzle. Alpha verion without splitting stuff into pieces.
2016-08-05 21:33:41 +02:00
db2b753446
Adjust media size for post script output
2016-08-03 22:20:13 +02:00
db38122125
Remove unnecessary moveTo() commands
...
.move() now leaves some space around parts
2016-08-03 22:20:13 +02:00
ea0b088356
Add reference length to allow checking the scaling
2016-07-31 18:28:57 +02:00
419cccc7dd
PlanetaryGear: add maxplanets and deltateeth params
2016-07-31 17:44:19 +02:00
6dd482be9c
Generate the list of generators automatically
...
Generate new traylayout class to make this work with the web interface
Minor fix to not error out in web interface for non existing doc string
2016-07-31 17:18:17 +02:00
b6d84b5c58
Mark generators which should not be shown in the web interface
2016-07-31 16:37:17 +02:00
77ba187c70
Name generator classes properly
2016-07-31 14:15:06 +02:00
f8b4ef2162
Remove DemoBox from boxes.__init__.py
2016-07-31 13:08:34 +02:00
776b0a2c27
Fix for extended function signature
2016-07-28 22:46:06 +02:00
6b30c60602
Fix parts and add hole parameter
...
Fix move params
Remove debugging frames
2016-07-27 23:32:36 +02:00
4cf33dae50
Move spacing out of the Edge margin() and into Boxes.move()
...
Also move ctx.save() and restoreinto Boxes.move().
Adjust (hopefully) all places using it.
2016-07-27 22:19:32 +02:00
558b63f20d
Fix size of base plate
...
Pass correct spoke_width
2016-07-25 23:37:12 +02:00
1849bfd5ab
New PlanetaryGear generator
2016-07-25 19:14:35 +02:00
7aac41339c
Add gearCarrier()
2016-07-25 18:59:50 +02:00
e3d552fe91
Allow passing a list of angles to generate_spokes()
2016-07-25 18:56:00 +02:00
1472d250bc
Draw spoke holes in correct direction (ccw)
2016-07-25 18:56:00 +02:00
2117bfbc15
Do not error out if drawing does into the negative x direction
...
... unless there is not enough place for the viewport.
2016-07-25 18:56:00 +02:00
c23b42a369
Fix size calculation for ring gears
2016-07-25 18:56:00 +02:00
354063068a
Fix parts.disc()
2016-07-25 18:52:48 +02:00
21948ade3b
Add ai, pdf output formats, tweak dxf and plt
2016-07-23 21:56:10 +02:00
284857d94a
Fix typo
2016-07-22 00:18:32 +02:00
575f41beff
Add param for gears
2016-07-19 19:37:21 +02:00
ed8ab9a364
Fix width of gearbox to make space for two big gears
2016-07-19 19:37:21 +02:00
a7728d8e32
New GearBox generator
2016-07-16 15:32:06 +02:00
113783ce32
Add method fro getting sizes of the gears
2016-07-16 15:26:46 +02:00
a344211a09
Add Parts class to collect stand alone parts like knobs
2016-07-15 18:32:37 +02:00
d6bd708db5
Python2 compat fix
2016-07-13 20:10:13 +02:00
5201138390
Add Pulley generator
2016-07-13 20:04:57 +02:00
8ce1c926cd
Add diameter() and getProfiles() (class) methods
2016-07-13 19:55:04 +02:00
bc50f3aeda
Fix GT2_2mm pulleys
2016-07-13 19:25:44 +02:00
01312788bb
Make Pulley a part with callback and move params
2016-07-13 17:41:51 +02:00
9cdb2e8dc4
Translate code from openscad to Boxes.py
2016-07-13 17:41:51 +02:00
9a7a291efc
Turn teeth data into valid Python
2016-07-13 17:41:51 +02:00
cc5fd1d651
Rename as Python module
2016-07-13 17:41:51 +02:00
90835b6493
Add pulley scad file
2016-07-13 17:41:51 +02:00
3abf95d665
Add callback and move param to regular gears
2016-07-13 17:41:44 +02:00
a2a2695c03
Support single callback that do not get any number
2016-07-13 17:38:50 +02:00
4dd61691d2
Remove no longer needed code
2016-07-13 17:38:50 +02:00
8eea323718
Add gears to Boxes class
2016-07-13 17:37:57 +02:00
2a849e7af6
Enable support for rack gears
2016-07-13 17:37:50 +02:00
0b963f30a1
Fix units to mm
2016-07-13 17:31:36 +02:00
c0a9d42abd
Cleanups and outer circle for inner gears
2016-07-13 17:31:35 +02:00
c6b4fcc588
Centercross and pitchcircle
2016-07-13 17:31:35 +02:00
b86146fe1c
Make generate_spokes a method and port it to boxes
2016-07-13 17:31:32 +02:00
Florian Festi
chrysn
Germain Lemasson
Martin Müller
Wayne Wylupski
jens persson
Alexander Bulimov
Rotzbua
Marius Bergmann
Sebastian Reichel
Stefan Grosshauser
Daniela Festi
Florian Festi
christopher
schinken