* list_ref can become LUA_REFNIL, because that's what rawgeti returns
for LUA_NOREF. Defensively guard for this, rather than falling into
the sntp_dolookups loop with nil on the stack.
* set_repeat_mode should not call itself, but should rather always do
what it's going to do and then optionally do the rest if directed.
* sntp_sync should not try to special case the single string argument:
we should be queueing that name for DNS resolution, too. Towards that
end, if we are given a single string, build a table and make that the
list_ref and call off to sntp_dolookups, just like we otherwise do.
FIXES: #2699
The PR removed the bulk of non-newlib headers from the NodeMCU source base.
app/libc has now been cut down to the bare minimum overrides to shadow the
corresponding functions in the SDK's libc. The old c_xyz.h headerfiles have been
nuked in favour of the standard <xyz.h> headers, with a few exceptions over in
sdk-overrides. Again, shipping a libc.a without headers is a terrible thing to do. We're
still living on a prayer that libc was configured the same was as a default-configured
xtensa gcc toolchain assumes it is. That part I cannot do anything about, unfortunately,
but it's no worse than it has been before.
This enables our source files to compile successfully using the standard header files,
and use the typical malloc()/calloc()/realloc()/free(), the strwhatever()s and
memwhatever()s. These end up, through macro and linker magic, mapped to the
appropriate SDK or ROM functions.
* mqtt:connect() secure parameter should be boolean
Continue to honor the old 0/1 values, but make them undocumented and add
a deprecation warning to the code and docs. Eventually, this should go
away.
* mqtt: rip out deprecated autoreconnect
* mqtt: expose all the callbacks via :on
* Use cross-browser JS for query params in EUS
* Update EUS doc to explain how to use parameters
* Remove ; in Lua code
* Rewrite the endpoint table
* Do not use properties as global Lua variables
* remove enduser_setup.html.gz
* rename folder 'eus' to 'enduser_setup'
* Change input type for password to "password"
* Replace outdated captive portal screen shot
* Upgrade u8g2 and add updateDisplayArea bindings
* u8g2 2.25.10
* add displays for 2.24.3 and 2.25.10
* remove workaround for hal pointer and make use of u8x8's user_ptr
* fix doc
* add binding for `updateDisplay()`
* Lua string optimisation in file.c + get/put contents methods
* Doc fix: move putcontents() into correct alphabetic order slot in list of static methods
* Rebaseline firmware to non-OS SDK version 3.0
* Note that SDK version 3.0 introduces the concept of a Flash Partition Table(PT). This is located at Flash offset 0x10000 in our firmware build.
* The firmware is now PT aware with both LFS and SPIFFS taking their partition size and location from the PT
* A new tool `tools/nodemcu-partition.py` is now used to initialise these data and can also download LFS and SPIFFS images to these partitions.
* I2C driver speed-up, i2c.SLOW, i2c.FAST and user-defined speed selection
* - Multiple buses (up to 10) with different speeds on each bus
- Standard(Slow, 100kHz), Fast(400kHz) and FastPlus(1MHz) modes or an
arbitrary clock speed
- Sharing SDA line over multiple I²C buses to save available pins
- GPIO16 pin can be used as SCL pin, but it does not support clock
stretching and selected bus will be limited to FAST speed.
* Dynamic memory allocation, error checks, simplification, timing tweaks.
* Separated the code of old driver for better compatibility and simplicity
* Change of driver interface
* Add bus status check in setup(); simplify getDC(); remove unnesessary lines in ACK read/write
* Fix for moved doc file and trailing whitespaces
* Update TLS protocol support
TLS1.0 is past PCI's EOL; BEAST is no more
Enable elliptic curve key exchanges
Do not enable the smallest ECs for security
Do not enable the largest ECs for computational time
Do not enable 25519 (sad) because it doesn't go across the wire
Drop non-PFS key exchanges
Drop ARC4, Blowfish, DES, genprime, XTEA code
Drop renegotiation support completely
It takes so much heap that it's not likely to work out well
Tidy handling of SSL_BUFFER_SIZE
Update docs
Drop mention of startcom, since they are no more, for letsencrypt
* Update mbedtls to 2.7.7
Preserve our vsnprintf and platform hacks
* Introduce TLS maximum fragment size knob
Reduce buffer size to 4Ki by default and advertize that. That's the
largest we can advertize with the TLS MFL extension, so there's no
point in making them larger. The truly adventurous can re-raise
SSL_BUFFER_SIZE and undefine the SSL_MAX_FRAGMENT_LENGTH_CODE and get
back to the earlier behavior.
* Default to mbedTLS debug with DEVELOP_VERSION
* Add spi.set_clock_div
This will allow the SPI clock divider to be changed relatively simply,
to better support multiple devices with varying SPI clock rate support
* Add documentation
* MQTT: handle large/chunked/fragmented messages properly
If a message spans multiple TCP packets it must be buffered before
delivered to LUA. Prior code did not do this at all, so this "patch"
really adds proper handling of fragmented MQTT packets.
This could also occur if multiple small messages was sent in a
single TCP packet, and the last message did not completely fit in that
packet.
Introduces a new option to the mqtt.Client constructor:
max_publish_length which defaults to 1024
Introduces a new 'overflow' callback.
Fixes issue #2308 and proper fix for PR #2544.
* mqtt.md: clarified heap allocation
* mqtt: ensure ack is sent for overflowed publish
If QoS is used we should still acknowledge that we received it, or server might retransmit it later.
Terry Ellison
Nathaniel Wesley Filardo
Gregor Hartmann
Johny Mattsson
Johny Mattsson
Philip Gladstone
Marcel Stör
Arnim Läuger
galjonsfigur
Nikolay Fiykov
Nathaniel Wesley Filardo
Natalia
sergio
Javier Peletier
andyleap
Johan Ström