- Lots of minor but nasty bugfixes to get all tests to run clean
- core lua and test suite fixes to allow luac -F to run cleanly against test suite
- next tranch to get LFS working
- luac.cross -a options plus fixes from feedback
- UART fixes and lua.c merge
- commit of wip prior to rebaselining against current dev
- more tweaks
The PR removed the bulk of non-newlib headers from the NodeMCU source base.
app/libc has now been cut down to the bare minimum overrides to shadow the
corresponding functions in the SDK's libc. The old c_xyz.h headerfiles have been
nuked in favour of the standard <xyz.h> headers, with a few exceptions over in
sdk-overrides. Again, shipping a libc.a without headers is a terrible thing to do. We're
still living on a prayer that libc was configured the same was as a default-configured
xtensa gcc toolchain assumes it is. That part I cannot do anything about, unfortunately,
but it's no worse than it has been before.
This enables our source files to compile successfully using the standard header files,
and use the typical malloc()/calloc()/realloc()/free(), the strwhatever()s and
memwhatever()s. These end up, through macro and linker magic, mapped to the
appropriate SDK or ROM functions.
* Upgrade u8g2 and add updateDisplayArea bindings
* u8g2 2.25.10
* add displays for 2.24.3 and 2.25.10
* remove workaround for hal pointer and make use of u8x8's user_ptr
* fix doc
* add binding for `updateDisplay()`
* Rebaseline firmware to non-OS SDK version 3.0
* Note that SDK version 3.0 introduces the concept of a Flash Partition Table(PT). This is located at Flash offset 0x10000 in our firmware build.
* The firmware is now PT aware with both LFS and SPIFFS taking their partition size and location from the PT
* A new tool `tools/nodemcu-partition.py` is now used to initialise these data and can also download LFS and SPIFFS images to these partitions.
* I2C driver speed-up, i2c.SLOW, i2c.FAST and user-defined speed selection
* - Multiple buses (up to 10) with different speeds on each bus
- Standard(Slow, 100kHz), Fast(400kHz) and FastPlus(1MHz) modes or an
arbitrary clock speed
- Sharing SDA line over multiple I²C buses to save available pins
- GPIO16 pin can be used as SCL pin, but it does not support clock
stretching and selected bus will be limited to FAST speed.
* Dynamic memory allocation, error checks, simplification, timing tweaks.
* Separated the code of old driver for better compatibility and simplicity
* Change of driver interface
* Add bus status check in setup(); simplify getDC(); remove unnesessary lines in ACK read/write
* Fix for moved doc file and trailing whitespaces
Files changed only by the author of FatFS (only updated to new version):
- 00history.txt
- 00readme.txt
- ff.c
- ff.h
- ffunicode.c
- diskio.h
- integer.h
- files in `option` folder except `syscall.c`
Changes:
- removed option folder (now everything is in ffunicode.c)
- modified Makefile to support new version of FatFS
- removed syscall.c and modified ffsystem.c from FatFS author instead
- modified files: diskio.c, ffconf.h to mimic changes from new version
- modified files: fatfs_config.h, myfatfs.c
because of changes of configuration keywords in 0.13 version
- removed empty lines from beginning of files:
fatfs_prefix_lib.h, myfatfs.c, sdcard.c
- changed version number in documentation
* Fix some subtle timing issues with gpio.pulse
* Add the pulse:update method
* Allow getstate to work on stopped pulsers
* Make gpio.mode(, gpio.OUTPUT) actually set the output mode
* Added some more documentation
* Add support of counting of interrupts
* Update the timestamp when interrupt happens during dispatch. Also
clear out interrupts when setting up a new callback
* Check the return code of the read function when doing crypto.fhash so that we don't pass negative lengths to the hashing functions
* Fix various assert failures in the LVM arising from rotables. No functional change
* Add the gpio interrupt time to the callback (and pass it from the interrupt handler)
* Get the PC right in the perf module
* Make the headers static in the websocket module
* Fix the documentation
* Add FatFs
* enable BUILD_FATFS for all-module build
* push vfs into rest of firmware
* align maximum filename length
* increase timeout for acmd41 during card initialization
* switch from DOS to Unix path semantics chdrive() is substituted by chdir()
* update to fatfs R.012a incl. patches 1-6
* add callback for rtc provisioning in file
* update docs
Fixes#1164 and thus also #1150, #1149, #1147 and #898.
* Move to latest version of SPIFFS
* Add SPIFFS porting layer for NodeMCU
* Add option to delete output if it doesn't fit
* Change FLASHSIZE to be in bits by default: default 4mb 32mb
* Add SPIFFS_MAX_FILESYSTEM_SIZE override
* Add notes on SPIFFS_FIXED_LOCATION
* Add 1M boundary
* Include the current version of the LICENSE
- Stop fighting against the SDK in terms of owning/writing the init_data block.
NodeMCU included a default init_data block because originally the SDK did
not, but by now it's not needed.
- Expose a way to reconfigure the ADC mode from Lua land. With most people
using the cloud builder and not able to change the #define for byte 107
this has been a pain point.
- Less confusion about which init_data has been used. Lua code can now simply
state what mode it wants the ADC to be in, and not worry about the rest of
the init_data complexities such as the init_data changing location due to
flashing with wrong flash_size setting, or doing/not doing a chip-erase
before loading new NodeMCU firmware.
Terry Ellison
Nikolay Fiykov
Johny Mattsson
Johny Mattsson
Arnim Läuger
Natalia
sergio
Philip Gladstone
galjonsfigur
dnc40085
Marcel Stör
Marcel Stör
Verne Roberts
moononournation