* list_ref can become LUA_REFNIL, because that's what rawgeti returns
for LUA_NOREF. Defensively guard for this, rather than falling into
the sntp_dolookups loop with nil on the stack.
* set_repeat_mode should not call itself, but should rather always do
what it's going to do and then optionally do the rest if directed.
* sntp_sync should not try to special case the single string argument:
we should be queueing that name for DNS resolution, too. Towards that
end, if we are given a single string, build a table and make that the
list_ref and call off to sntp_dolookups, just like we otherwise do.
FIXES: #2699
The PR removed the bulk of non-newlib headers from the NodeMCU source base.
app/libc has now been cut down to the bare minimum overrides to shadow the
corresponding functions in the SDK's libc. The old c_xyz.h headerfiles have been
nuked in favour of the standard <xyz.h> headers, with a few exceptions over in
sdk-overrides. Again, shipping a libc.a without headers is a terrible thing to do. We're
still living on a prayer that libc was configured the same was as a default-configured
xtensa gcc toolchain assumes it is. That part I cannot do anything about, unfortunately,
but it's no worse than it has been before.
This enables our source files to compile successfully using the standard header files,
and use the typical malloc()/calloc()/realloc()/free(), the strwhatever()s and
memwhatever()s. These end up, through macro and linker magic, mapped to the
appropriate SDK or ROM functions.
* mqtt:connect() secure parameter should be boolean
Continue to honor the old 0/1 values, but make them undocumented and add
a deprecation warning to the code and docs. Eventually, this should go
away.
* mqtt: rip out deprecated autoreconnect
* mqtt: expose all the callbacks via :on
* Use cross-browser JS for query params in EUS
* Update EUS doc to explain how to use parameters
* Remove ; in Lua code
* Rewrite the endpoint table
* Do not use properties as global Lua variables
* remove enduser_setup.html.gz
* rename folder 'eus' to 'enduser_setup'
* Change input type for password to "password"
* Replace outdated captive portal screen shot
* Upgrade u8g2 and add updateDisplayArea bindings
* u8g2 2.25.10
* add displays for 2.24.3 and 2.25.10
* remove workaround for hal pointer and make use of u8x8's user_ptr
* fix doc
* add binding for `updateDisplay()`
* Lua string optimisation in file.c + get/put contents methods
* Doc fix: move putcontents() into correct alphabetic order slot in list of static methods
* Rebaseline firmware to non-OS SDK version 3.0
* Note that SDK version 3.0 introduces the concept of a Flash Partition Table(PT). This is located at Flash offset 0x10000 in our firmware build.
* The firmware is now PT aware with both LFS and SPIFFS taking their partition size and location from the PT
* A new tool `tools/nodemcu-partition.py` is now used to initialise these data and can also download LFS and SPIFFS images to these partitions.
* I2C driver speed-up, i2c.SLOW, i2c.FAST and user-defined speed selection
* - Multiple buses (up to 10) with different speeds on each bus
- Standard(Slow, 100kHz), Fast(400kHz) and FastPlus(1MHz) modes or an
arbitrary clock speed
- Sharing SDA line over multiple I²C buses to save available pins
- GPIO16 pin can be used as SCL pin, but it does not support clock
stretching and selected bus will be limited to FAST speed.
* Dynamic memory allocation, error checks, simplification, timing tweaks.
* Separated the code of old driver for better compatibility and simplicity
* Change of driver interface
* Add bus status check in setup(); simplify getDC(); remove unnesessary lines in ACK read/write
* Fix for moved doc file and trailing whitespaces
* DHT11 read sometimes failed with checksum error.
The code assumed DHT11 devices only ever return zero in the temperature and humidity decimal fraction bytes. The datasheet doesn't guarantee this is the case, and by observation I have noticed that indeed the DHT11 may sometimes return another number, usually close to zero. This means that the code would fail with a checksum error, as the fraction bytes were not included when the checksum was calculated. These bytes are now taken into account and also returned as part of the measurement.
This also means that the related dht.read() function is non-functional. If you have a DHT11 device that returns a non-zero decimal part, dht.read() will interpret it as a DHT22 result and return the wrong measurement. For this reason dht.read() should be retired. This patch does not address this issue.
A block of memory is accessed after having been freed. This was obscured by the fact that 'oBuf' is a pointer into the middle of the block 'dynamicTables', so when dynamicTables is freed, oBuf is pointing to freed memory. Occasionally, luac.cross would crash because of this.
Files changed only by the author of FatFS (only updated to new version):
- 00history.txt
- 00readme.txt
- ff.c
- ff.h
- ffunicode.c
- diskio.h
- integer.h
- files in `option` folder except `syscall.c`
Changes:
- removed option folder (now everything is in ffunicode.c)
- modified Makefile to support new version of FatFS
- removed syscall.c and modified ffsystem.c from FatFS author instead
- modified files: diskio.c, ffconf.h to mimic changes from new version
- modified files: fatfs_config.h, myfatfs.c
because of changes of configuration keywords in 0.13 version
- removed empty lines from beginning of files:
fatfs_prefix_lib.h, myfatfs.c, sdcard.c
- changed version number in documentation
Gregor Hartmann
Nathaniel Wesley Filardo
Terry Ellison
Johny Mattsson
Johny Mattsson
Philip Gladstone
Marcel Stör
Arnim Läuger
galjonsfigur
Nikolay Fiykov
ziggurat29
Nathaniel Wesley Filardo
Natalia
sergio
Mark Schlögel
Javier Peletier