- Lots of minor but nasty bugfixes to get all tests to run clean
- core lua and test suite fixes to allow luac -F to run cleanly against test suite
- next tranch to get LFS working
- luac.cross -a options plus fixes from feedback
- UART fixes and lua.c merge
- commit of wip prior to rebaselining against current dev
- more tweaks
The PR removed the bulk of non-newlib headers from the NodeMCU source base.
app/libc has now been cut down to the bare minimum overrides to shadow the
corresponding functions in the SDK's libc. The old c_xyz.h headerfiles have been
nuked in favour of the standard <xyz.h> headers, with a few exceptions over in
sdk-overrides. Again, shipping a libc.a without headers is a terrible thing to do. We're
still living on a prayer that libc was configured the same was as a default-configured
xtensa gcc toolchain assumes it is. That part I cannot do anything about, unfortunately,
but it's no worse than it has been before.
This enables our source files to compile successfully using the standard header files,
and use the typical malloc()/calloc()/realloc()/free(), the strwhatever()s and
memwhatever()s. These end up, through macro and linker magic, mapped to the
appropriate SDK or ROM functions.
* I2C driver speed-up, i2c.SLOW, i2c.FAST and user-defined speed selection
* - Multiple buses (up to 10) with different speeds on each bus
- Standard(Slow, 100kHz), Fast(400kHz) and FastPlus(1MHz) modes or an
arbitrary clock speed
- Sharing SDA line over multiple I²C buses to save available pins
- GPIO16 pin can be used as SCL pin, but it does not support clock
stretching and selected bus will be limited to FAST speed.
* Dynamic memory allocation, error checks, simplification, timing tweaks.
* Separated the code of old driver for better compatibility and simplicity
* Change of driver interface
* Add bus status check in setup(); simplify getDC(); remove unnesessary lines in ACK read/write
* Fix for moved doc file and trailing whitespaces
* pmsleep refactor
* Shortened swtmr disabled message
* Added swtimer debug module option to user_modules.h.
* Added comments to user_config.h.
* Fixed error in documentation for node.sleep()
* remove blank sntp.c that got added in during rebase onto dev(6218b92)
* Added #ifdefs around SWTIMER_REG_CB to prevent inclusion of disabled
code
Initial commit for
https://github.com/nodemcu/nodemcu-firmware/issues/2225 .
Replay patches from Espressif's repository at
https://github.com/espressif/ESP8266_NONOS_SDK between tags v2.1.0 and
v2.2.0:
0001-sync-from-ccca00f2.patch
Superseded by existing changes, but lines reordered in app/driver/key.c
to minimize divergences.
0002-sync-from-3f38ad5a.patch
Upstream files only
0003-Update-links.patch
Not meaningful to NodeMCU
0004-sync-from-01990ad0.patch
0005-sync-from-cdf6877d.patch
Upstream files only
0006-sync-from-f29e744c.patch
Upstream files only, user_interface.h override non-conflicting
0009-feat-lwip-Move-lwip-source-code-to-third_party-folde.patch
Merged change to lwip/app/espconn_udp.c; rest is just moves or
appears to not apply.
0010-feat-mbedtls-Add-mbedtls-source-code-in-third_party-.patch
Does not apply; we use our own mbedtls
0011-added-C-support.patch
Merged to Makefile
0012-feat-mbedtls-Rebuild-libmbedtls.patch
Already applied
0013-fix-at-Fix-some-bugs-of-AT.patch
Upstream files only
0014-feat-err_t-Redefine-err_t-to-s32_t.patch
Merged to app/include/arch/cc.h and ./app/include/lwip/app/espconn.h;
the rest is upstream files.
0015-fix-wpa-Fix-wpa-wpa2-ptk-gtk-reinstallation-vulnerab.patch
0016-fix-wifi-Remove-group-key-entry-before-connecting-to.patch
0017-feat-lib-Remove-time-function-in-libmain.patch
Upstream files only
0018-feat-espconn-Modification-for-espconn.patch
Merged to app/include/lwip/app/espconn.h,
app/include/lwip/app/espconn_tcp.h, app/lwip/app/espconn.c,
app/lwip/app/espconn_tcp.c
0019-feat-at-Use-new-espconn_recv-to-fix-tcp-server-issue.patch
0020-feat-examples-Update-mqtt-demo-and-auto-bin-generate.patch
Upstream files only
0021-wifi-Add-scan-threshold-and-dwell-time.patch
0022-feat-wifi-Add-country-code-API.patch
0023-feat-wifi-Record-more-information-of-scanned-ap.patch
Upstream files only, user_interface.h override non-conflicting
0024-fix-example-Fix-IoT_Demo-user-sector-error.patch
Upstream files only
0025-fix-lwip-Fix-sequence-number-error-of-RST-ACK.patch
Merged app/lwip/core/tcp_in.c
0026-fix-mbedtls-Fix-memory-leak.patch
Merged app/mbedtls/app/lwIPSocket.c
0027-fix-mbedtls-Fix-call-send-callback-function-failed.patch
Merged app/mbedtls/app/espconn_mbedtls.c
0028-feat-Add-USE_OPTIMIZE_PRINTF-in-third_party-Makefile.patch
Merged app/Makefile
0029-fix-api-Fix-ets_delay_us-declaration.patch
Upstream files only, osapi.h override non-conflicting
0030-fix-wifi-Remove-max_tx_power-in-wifi_country_t-in-li.patch
0031-fix-wifi-Fix-softAP-wrong-behavior-after-call-system.patch
0032-fix-wifi-bugfix-of-scan-fail-after-connected-if-max-.patch
0033-feat-at-Enable-scan-time-scan-type-and-add-scan-resu.patch
0034-feat-at-Add-command-AT-CWCOUNTRY.patch
0035-fix-at-Fix-that-AT-CIPSTART-causes-busy-if-the-serve.patch
Upstream files only
0036-feat-mbedtls-Speed-up-mbedtls-handshake-process.patch
Merged app/mbedtls/app/espconn_mbedtls.c
0037-fix-api-Fix-os_calloc-declaration.patch
Merged app/include/lwip/mem.h; sdk-overrides/include/mem.h
non-conflicting.
0038-fix-mbedtls-Fix-disconnect-callback-function-never-b.patch
Merged app/mbedtls/app/espconn_mbedtls.c; minor revision to logic in
6576af959b. Whitespace fixes.
0039-feat-at-Add-country-code-start-channel-in-AT-CWCOUNT.patch
0040-fix-net80211-Fix-Null-pointer-in-ieee80211_rfid_locp.patch
Upstream files only
0041-feat-wifi-Add-new-esp_init_data_default-v08-bin.patch
Upstream files only, but impacts Makefile
0042-fix-mbedtls-Fix-load-cert-fail-when-the-private-key-.patch
Merged app/mbedtls/app/espconn_mbedtls.c
0043-fix-wifi-The-start-channel-can-be-any-valid-channel.patch
0044-fix-wifi-Fix-scan-do-not-start-after-connect.patch
0045-feat-wifi-Add-keep-connection-for-station-to-keep-co.patch
0046-feat-at-Update-AT-version-to-1.6.0.0.patch
0047-fix-at-Fix-GSLP-too-long-time.patch
0048-fix-at-Fix-the-message-is-incorrect-when-creating-UD.patch
0049-feat-at-Add-AT-CIPSERVERMAXCONN.patch
Upstream files only
0050-feat-system-Add-softap-distributes-station-ip-event.patch
Upstream files only, user_interface.h override non-conflicting
0051-feat-example-Use-libmbedtls.a-instead-of-libssl.a-in.patch
Upstream files only
0052-feat-mesh-Remove-mesh-support.patch
Upstream files only, but go ahead and remove comment from
ld/nodemcu.ld.
0053-fix-example-Fix-forget-to-add-integer-parameter-when.patch
Upstream files only
0054-fix-mbedtls-Fix-reconnect_callback-is-not-triggered-.patch
Merged app/mbedtls/app/espconn_mbedtls.c
0055-feat-at-Add-AT-SYSMSG-to-enable-some-report-informat.patch
0056-fix-at-Fix-the-incorrect-link-id-when-client-connect.patch
0057-fix-at-Fix-the-bug-that-it-should-be-error-when-the-.patch
0058-fix-smartconfig-Fix-the-smartconfig-scan-time-issue.patch
0059-fix-lwip-Fix-the-bug-of-lwip-output.patch
Upstream files only
0060-fix-lwip-Fix-the-length-of-TCP-data-in-one-packet-is.patch
0061-fix-lwip-Fix-send-TCP-data-with-two-or-more-pbuf.patch
Merged app/lwip/core/tcp_out.c
0062-fix-wifi-Fix-assert-happen-when-smartconfig-start-th.patch
Upstream files only
0063-fix-mbedtls-Fix-memory-leak-when-ESP8266-as-SSL-TLS-.patch
Merged app/mbedtls/app/espconn_mbedtls.c
0064-fix-mbedtls-Fix-already-freed-and-exception-bug-when.patch
Merged app/mbedtls/app/lwIPSocket.c
0065-fix-at-Fix-bug-that-there-is-no-result-when-sending-.patch
0066-feat-example-Add-AT-bin-version.patch
0067-feat-version-Update-version-to-2.2.0-and-add-version.patch
0068-feat-bin-Update-AT-bin-for-SDK-2.2.0.patch
Upstream files only
Apply local changes to build:
app/include/lwip/app/espconn.h pulls changes (and license decl) from
upstream SDK. Makefile is altered to use this file ahead of the
SDK's.
Remove lwip's sntp support, since it was never really wired in anyway.
See https://github.com/nodemcu/nodemcu-firmware/issues/2042 for more
information. Patch Makefile to strip time.o, the consumer of lwip's
sntp functionality, from libmain.a, resulting in much
easier-to-understand error messages.
This has consequences for mbedtls. The simplest thing to do, which is,
impressively, not a change in behavior, is to completely disable TLS
certificate time validation; a later patch can optionally couple this to
RTCTIME support.
Similarly, it happens that the sqlite3 import was calling time(), but
this was not going to work out well for it. Just stub it out to always
return unix timestamp 0, as would have happened anyway.
Changes unprocessed:
0007-sync-from-080c37e1.patch
0008-feat-lib-Compile-some-libraries-with-ffunction-secti.patch
These two make changes to the linker script; perhaps
they are worth porting over, but I have not done so
here.
This is build-tested (ADC, BIT, COLOR_UTILS, CRON, CRYPTO, DHT, ENCODER,
FILE, GPIO, HTTP, I2C, MQTT, NET, NODE, OW, PCM, PERF, PWM, RTCFIFO,
RTCMEM, RTCTIME, SNTP, SPI, SQLITE3, STRUCT, TLS, TMR, UART, WIFI,
WS2812, WS2812_EFFECTS) and boots, but only limited run-time testing has
been performed. Testing done does, however, include having made a few
TLS connections through the HTTP module, so things are not hopelessly
broken, at the very least.
Input during startup (especially while doing initial filesystem format)
ran the risk of filling up the task queue, preventing the start_lua task
from being queued, and hence NodeMCU would not start up that time.
* Initial version of gdbstub support
* Add DEBUG argument to Makefile to add more debug data and turn off -Os
* Add the output redirection handling
* Added documentation
* Cleaned up the english a bit
* Make gdboutput actually trap all the output
* Review comments
* Add FatFs
* enable BUILD_FATFS for all-module build
* push vfs into rest of firmware
* align maximum filename length
* increase timeout for acmd41 during card initialization
* switch from DOS to Unix path semantics chdrive() is substituted by chdir()
* update to fatfs R.012a incl. patches 1-6
* add callback for rtc provisioning in file
* update docs
* Corrected CPOL/CPHA relationships
* Simplified to remove duplicated code
* Removed comments about when MISO is sampled. ESP seems to sample MISO on same clock edge as when MOSI is set.
commit 2c7c3fc3985cc32866e8af496abea9971eaee90a
Merge: 9179dae 41022c3
Author: philip <philip@gladstonefamily.net>
Date: Sun Feb 28 14:47:47 2016 -0500
Merge remote-tracking branch 'upstream/dev' into rotary_2
commit 9179dae0824e6b35ad09e5113aacc26dc91692c0
Author: philip <philip@gladstonefamily.net>
Date: Fri Feb 26 20:53:27 2016 -0500
Review comments
commit 67741170e20ccb2b636e701f0664feff2aafbb4c
Author: philip <philip@gladstonefamily.net>
Date: Fri Feb 26 20:59:49 2016 -0500
Squashed commit of the following:
commit 8c9a64731c4a8b9aedda18a399b433b173d2199f
Merge: 085935f 19d3c1d
Author: philip <philip@gladstonefamily.net>
Date: Fri Feb 26 20:58:10 2016 -0500
Merge remote-tracking branch 'upstream/dev' into rotarymod
Conflicts:
app/platform/platform.c
commit 085935fc56986d607ff5e05d1663970331959c34
Author: philip <philip@gladstonefamily.net>
Date: Fri Feb 26 20:53:27 2016 -0500
Review comment
commit 7732fd2d1044f28b8fcf5b0aa0f76d76fe80f449
Author: philip <philip@gladstonefamily.net>
Date: Sat Feb 20 12:10:38 2016 -0500
Module to handle rotary decoders
Eliminate ROTARY_DEBUG
Remove unused file
Eliminate a malloc call
Cleaned up the register code. Now 0x114 bytes
Fix bug with clearing bits in one case
Fix the type in the #define name
As with the last commit this rolls up the follwowing, but include the various
review comments on the PR.
- **Documentation changes**. I've added the taks FAQ as a stub new Extension
developer FAQ, and split the old FAQ into a Lua Developer FAQ and a Hardware
FAQ.
- **Tasking I/F**. New `app/task/Makefile`, `app/task/task.c`,
`app/include/task/task.h` and `app/Makefile` as per previous commit. Cascade
changes to `app/driver/uart.c`, `app/include/driver/uart.h`,
`app/user/user_main.c` and `app/modules/node.c`
- **GPIO Rework** to `app/modules/gpio.c` and `pin_map.[hc]`, `platform.[hc]`
in `app/platform`
- **Other Optimisations** Move the `platform_*_exists()` from
`app/platform/common.c` to static inline declarations in `platform.h` as
this generates faster, smaller code. Move lgc.a routines out of iram0.