563 lines
15 KiB
Markdown
563 lines
15 KiB
Markdown
# WiFi Module
|
|
| Since | Origin / Contributor | Maintainer | Source |
|
|
| :----- | :-------------------- | :---------- | :------ |
|
|
| 2016-10-03 | [Johny Mattsson](https://github.com/jmattsson) |[Johny Mattsson](https://github.com/jmattsson) | [wifi.c](../../components/modules/wifi.c)|
|
|
|
|
|
|
The NodeMCU WiFi control is spread across several tables:
|
|
|
|
- `wifi` for overall WiFi configuration
|
|
- [`wifi.sta`](#wifista-module) for station mode functions
|
|
- [`wifi.ap`](#wifiap-module) for access point (AP) functions
|
|
|
|
## wifi.getchannel()
|
|
|
|
Gets the current WiFi channel.
|
|
|
|
#### Syntax
|
|
`wifi.getchannel()`
|
|
|
|
#### Parameters
|
|
`nil`
|
|
|
|
#### Returns
|
|
- current WiFi channel (primary channel)
|
|
- HT20/HT40 information (secondary channel). One of the constants:
|
|
- `wifi.HT20 `
|
|
- `wifi.HT40_ABOVE`
|
|
- `wifi.HT40_BELOW`
|
|
|
|
## wifi.getmode()
|
|
|
|
|
|
Gets WiFi operation mode.
|
|
|
|
#### Syntax
|
|
`wifi.getmode()`
|
|
|
|
#### Parameters
|
|
`nil`
|
|
|
|
#### Returns
|
|
The WiFi mode, as one of the `wifi.STATION`, `wifi.SOFTAP`, `wifi.STATIONAP` or `wifi.NULLMODE` constants.
|
|
|
|
#### See also
|
|
[`wifi.mode()`](#wifimode)
|
|
|
|
|
|
## wifi.mode()
|
|
|
|
Configures the WiFi mode to use. NodeMCU can run in one of four WiFi modes:
|
|
|
|
- Station mode, where the NodeMCU device joins an existing network
|
|
- Access point (AP) mode, where it creates its own network that others can join
|
|
- Station + AP mode, where it both creates its own network while at the same time being joined to another existing network
|
|
- WiFi off
|
|
|
|
When using the combined Station + AP mode, the same channel will be used for both networks as the radio can only listen on a single channel.
|
|
|
|
#### Syntax
|
|
`wifi.mode(mode[, save])`
|
|
|
|
#### Parameters
|
|
- `mode` value should be one of
|
|
- `wifi.STATION` for when the device is connected to a WiFi router. This is often done to give the device access to the Internet.
|
|
- `wifi.SOFTAP` for when the device is acting *only* as an access point. This will allow you to see the device in the list of WiFi networks (unless you hide the SSID, of course). In this mode your computer can connect to the device, creating a local area network. Unless you change the value, the NodeMCU device will be given a local IP address of 192.168.4.1 and assign your computer the next available IP address, such as 192.168.4.2.
|
|
- `wifi.STATIONAP` is the combination of `wifi.STATION` and `wifi.SOFTAP`. It allows you to create a local WiFi connection *and* connect to another WiFi router.
|
|
- `wifi.NULLMODE` disables the WiFi interface(s). Use `wifi.stop()` to fully shut down the WiFi interface.
|
|
- `save` choose whether or not to save wifi mode to flash
|
|
- `true` WiFi mode configuration **will** be retained through power cycle. (Default)
|
|
- `false` WiFi mode configuration **will not** be retained through power cycle.
|
|
|
|
#### Returns
|
|
current mode after setup
|
|
|
|
#### Example
|
|
```lua
|
|
wifi.mode(wifi.STATION)
|
|
```
|
|
|
|
#### See also
|
|
[`wifi.getmode()`](#wifigetmode)
|
|
[`wifi.stop()`](#wifistop)
|
|
|
|
|
|
## wifi.start()
|
|
|
|
Starts the WiFi interface(s). On system startup the WiFi interface(s) are
|
|
not running. This is to enable users to choose whether to expend the power
|
|
necessary for radio comms. A sensor device running on battery might only
|
|
want to enable WiFi every 10th boot for example.
|
|
|
|
If station mode is configured with `auto` set to true, the chip will attempt
|
|
to join the configured network at this point.
|
|
|
|
#### Syntax
|
|
`wifi.start()`
|
|
|
|
#### Parameters
|
|
`nil`
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### See also
|
|
[`wifi.stop()`](#wifistop)
|
|
|
|
|
|
## wifi.stop()
|
|
|
|
Shuts down the WiFi interface(s).
|
|
|
|
#### Syntax
|
|
`wifi.stop()`
|
|
|
|
#### Parameters
|
|
`nil`
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### See also
|
|
[`wifi.start()`](#wifistart)
|
|
|
|
|
|
# wifi.sta Module
|
|
|
|
## wifi.sta.config()
|
|
|
|
Sets the WiFi station configuration.
|
|
|
|
The WiFi mode must be set to `wifi.STATION` or `wifi.STATIONAP` before this
|
|
function can be used.
|
|
|
|
#### Syntax
|
|
`wifi.sta.config(station_config, save)`
|
|
|
|
#### Parameters
|
|
- `station_config` table containing configuration data for station
|
|
- `ssid` string which is less than 32 bytes.
|
|
- `pwd` string which is 8-64 or 0 bytes. Empty string indicates an open WiFi access point.
|
|
- `auto` defaults to true
|
|
- `true` to enable auto connect and connect to access point, hence with `auto=true` there's no need to call [`wifi.sta.connect()`](#wifistaconnect)
|
|
- `false` to disable auto connect and remain disconnected from access point
|
|
- `bssid` string that contains the MAC address of the access point (optional)
|
|
- You can set BSSID if you have multiple access points with the same SSID.
|
|
- Note: if you set BSSID for a specific SSID and would like to configure station to connect to the same SSID only without the BSSID requirement, you MUST first configure to station to a different SSID first, then connect to the desired SSID
|
|
- The following formats are valid:
|
|
- "DE:C1:A5:51:F1:ED"
|
|
- "AC-1D-1C-B1-0B-22"
|
|
- "DE AD BE EF 7A C0"
|
|
- "AcDc0123c0DE"
|
|
|
|
- `save` Save station configuration to flash.
|
|
- `true` configuration **will** be retained through power cycle.
|
|
- `false` configuration **will not** be retained through power cycle. (Default)
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### Example
|
|
|
|
```lua
|
|
--connect to Access Point (DO NOT save config to flash)
|
|
station_cfg={}
|
|
station_cfg.ssid="NODE-AABBCC"
|
|
station_cfg.pwd="password"
|
|
wifi.sta.config(station_cfg)
|
|
|
|
--connect to Access Point (DO save config to flash)
|
|
station_cfg={}
|
|
station_cfg.ssid="NODE-AABBCC"
|
|
station_cfg.pwd="password"
|
|
wifi.sta.config(station_cfg, true)
|
|
|
|
--connect to Access Point with specific MAC address
|
|
station_cfg={}
|
|
station_cfg.ssid="NODE-AABBCC"
|
|
station_cfg.pwd="password"
|
|
station_cfg.bssid="AA:BB:CC:DD:EE:FF"
|
|
wifi.sta.config(station_cfg)
|
|
|
|
--configure station but don't connect to Access point
|
|
station_cfg={}
|
|
station_cfg.ssid="NODE-AABBCC"
|
|
station_cfg.pwd="password"
|
|
station_cfg.auto=false
|
|
wifi.sta.config(station_cfg)
|
|
|
|
```
|
|
|
|
#### See also
|
|
- [`wifi.sta.connect()`](#wifistaconnect)
|
|
- [`wifi.sta.disconnect()`](#wifistadisconnect)
|
|
|
|
## wifi.sta.connect()
|
|
|
|
Connects to the configured AP in station mode. You only ever need to call this if auto-connect was disabled in [`wifi.sta.config()`](#wifistaconfig).
|
|
|
|
#### Syntax
|
|
`wifi.sta.connect()`
|
|
|
|
#### Parameters
|
|
`nil`
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### See also
|
|
- [`wifi.sta.disconnect()`](#wifistadisconnect)
|
|
- [`wifi.sta.config()`](#wifistaconfig)
|
|
|
|
## wifi.sta.disconnect()
|
|
|
|
Disconnects from AP in station mode.
|
|
|
|
!!! note
|
|
|
|
Please note that disconnecting from Access Point does not reduce power consumption much.
|
|
If power saving is your goal, please use [`wifi.stop()`](#wifisetmode).
|
|
|
|
#### Syntax
|
|
`wifi.sta.disconnect()`
|
|
|
|
#### Parameters
|
|
`nil`
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### See also
|
|
- [`wifi.sta.config()`](#wifistaconfig)
|
|
- [`wifi.sta.connect()`](#wifistaconnect)
|
|
|
|
|
|
## wifi.sta.on()
|
|
|
|
Registers callbacks for WiFi station status events.
|
|
|
|
#### Syntax
|
|
`wifi.sta.on(event, callback)`
|
|
|
|
#### Parameters
|
|
- `event` WiFi station event you would like to set a callback for:
|
|
- "start"
|
|
- "stop"
|
|
- "connected"
|
|
- "disconnected"
|
|
- "authmode_changed"
|
|
- "got_ip"
|
|
- `callback` callback `function(event, info)` to perform when event occurs,
|
|
or `nil` to unregister the callback for the event. The `info` argument
|
|
given to the callback is a table containing additional information about
|
|
the event.
|
|
|
|
Event information provided for each event is as follows:
|
|
|
|
- `start`: no additional info
|
|
- `stop`: no additional info
|
|
- `connected`: information about network/AP that was connected to:
|
|
- `ssid`: the SSID of the network
|
|
- `bssid`: the BSSID of the AP
|
|
- `channel`: the primary channel of the network
|
|
- `auth` authentication method, one of `wifi.OPEN`, `wifi.WPA_PSK`, `wifi.WPA2_PSK` (default), `wifi.WPA_WPA2_PSK`
|
|
- `disconnected`: information about the network/AP that was disconnected from:
|
|
- `ssid`: the SSID of the network
|
|
- `bssid`: the BSSID of the AP
|
|
- `reason`: an integer code for the reason (see table below for mapping)
|
|
- `authmode_changed`: authentication mode information:
|
|
- `old_mode`: the previous auth mode used
|
|
- `new_mode`: the new auth mode used
|
|
- `got_ip`: IP network information:
|
|
- `ip`: the IP address assigned
|
|
- `netmask`: the IP netmask
|
|
- `gw`: the gateway ("0.0.0.0" if no gateway)
|
|
|
|
Table containing disconnect reasons.
|
|
|
|
| Disconnect reason | value |
|
|
|:--------------------|:-------:|
|
|
|UNSPECIFIED | 1 |
|
|
|AUTH_EXPIRE | 2 |
|
|
|AUTH_LEAVE | 3 |
|
|
|ASSOC_EXPIRE | 4 |
|
|
|ASSOC_TOOMANY | 5 |
|
|
|NOT_AUTHED | 6 |
|
|
|NOT_ASSOCED | 7 |
|
|
|ASSOC_LEAVE | 8 |
|
|
|ASSOC_NOT_AUTHED | 9 |
|
|
|DISASSOC_PWRCAP_BAD | 10 |
|
|
|DISASSOC_SUPCHAN_BAD | 11 |
|
|
|IE_INVALID | 13 |
|
|
|MIC_FAILURE | 14 |
|
|
|4WAY_HANDSHAKE_TIMEOUT | 15 |
|
|
|GROUP_KEY_UPDATE_TIMEOUT | 16 |
|
|
|IE_IN_4WAY_DIFFERS | 17 |
|
|
|GROUP_CIPHER_INVALID | 18 |
|
|
|PAIRWISE_CIPHER_INVALID | 19 |
|
|
|AKMP_INVALID | 20 |
|
|
|UNSUPP_RSN_IE_VERSION | 21 |
|
|
|INVALID_RSN_IE_CAP | 22 |
|
|
|802_1X_AUTH_FAILED | 23 |
|
|
|CIPHER_SUITE_REJECTED | 24 |
|
|
|BEACON_TIMEOUT | 200 |
|
|
|NO_AP_FOUND | 201 |
|
|
|AUTH_FAIL | 202 |
|
|
|ASSOC_FAIL | 203 |
|
|
|HANDSHAKE_TIMEOUT | 204 |
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### Example
|
|
```lua
|
|
--register callback
|
|
wifi.sta.on("got_ip", function(ev, info)
|
|
print("NodeMCU IP config:", info.ip, "netmask", info.netmask, "gw", info.gw)
|
|
end)
|
|
|
|
--unregister callback
|
|
wifi.sta.on("got_ip", nil)
|
|
```
|
|
|
|
|
|
## wifi.sta.getmac()
|
|
Gets MAC address in station mode.
|
|
|
|
#### Syntax
|
|
`wifi.sta.getmac()`
|
|
|
|
#### Parameters
|
|
None
|
|
|
|
|
|
## wifi.sta.scan()
|
|
|
|
Scan for available networks.
|
|
|
|
#### Syntax
|
|
`wifi.sta.scan(cfg, callback)`
|
|
|
|
#### Parameters
|
|
- `cfg` table that contains scan configuration:
|
|
- `ssid` SSID == nil, don't filter SSID
|
|
- `bssid` BSSID == nil, don't filter BSSID
|
|
- `channel` channel == 0, scan all channels, otherwise scan set channel (default is 0)
|
|
- `hidden` hidden == 1, get info for router with hidden SSID (default is 0)
|
|
- `callback(ap_list)` a callback function to receive the list of APs when the scan is done. Each entry in the returned array follows the format used for [`wifi.sta.config()`](#wifistaconfig), with some additional fields.
|
|
|
|
The following fields are provided for each scanned AP:
|
|
|
|
- `ssid`: the network SSID
|
|
- `bssid`: the BSSID of the AP
|
|
- `channel`: primary WiFi channel of the AP
|
|
- `rssi`: Received Signal Strength Indicator value
|
|
- `auth` authentication method, one of `wifi.OPEN`, `wifi.WPA_PSK`, `wifi.WPA2_PSK` (default), `wifi.WPA_WPA2_PSK`
|
|
- `bandwidth`: one of the following constants:
|
|
- `wifi.HT20`
|
|
- `wifi.HT40_ABOVE`
|
|
- `wifi.HT40_BELOW`
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### Example
|
|
|
|
```lua
|
|
-- Scan and print all found APs, including hidden ones
|
|
wifi.sta.scan({ hidden = 1 }, function(err,arr)
|
|
if err then
|
|
print ("Scan failed:", err)
|
|
else
|
|
print(string.format("%-26s","SSID"),"Channel BSSID RSSI Auth Bandwidth")
|
|
for i,ap in ipairs(arr) do
|
|
print(string.format("%-32s",ap.ssid),ap.channel,ap.bssid,ap.rssi,ap.auth,ap.bandwidth)
|
|
end
|
|
print("-- Total APs: ", #arr)
|
|
end
|
|
end)
|
|
```
|
|
|
|
## wifi.sta.setip()
|
|
|
|
Sets IP address, netmask, gateway, dns address in station mode.
|
|
|
|
Options set by this function are not saved to flash.
|
|
|
|
#### Syntax
|
|
`wifi.sta.setip(cfg)`
|
|
|
|
#### Parameters
|
|
- `cfg` table to hold configuration:
|
|
- `ip` device ip address.
|
|
- `netmask` network netmask.
|
|
- `gateway` gateway address.
|
|
- `dns` name server address.
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### Example
|
|
```lua
|
|
cfg={}
|
|
cfg.ip=192.168.0.10
|
|
cfg.netmask=255.255.255.0
|
|
cfg.gateway=192.168.0.1
|
|
cfg.dns=8.8.8.8
|
|
wifi.sta.setip(cfg)
|
|
```
|
|
|
|
## wifi.sta.sethostname
|
|
|
|
Sets station hostname
|
|
|
|
Must be called before `wifi.sta.connect()`
|
|
|
|
Options set by this function are not saved to flash.
|
|
|
|
#### Syntax
|
|
`wifi.sta.sethostname(hostname)`
|
|
|
|
#### Returns
|
|
true if success, false otherwise
|
|
|
|
#### Parameters
|
|
`hostname` must only contain letters, numbers and hyphens('-') and be 32 characters or less with first and last character being alphanumeric
|
|
|
|
#### Example
|
|
```lua
|
|
wifi.sta.sethostname("ESP32")
|
|
```
|
|
|
|
# wifi.ap Module
|
|
|
|
## wifi.ap.config()
|
|
|
|
Configures the AP.
|
|
|
|
The WiFi mode must be set to `wifi.SOFTAP` or `wifi.STATIONAP` before this
|
|
function can be used.
|
|
|
|
#### Syntax
|
|
`wifi.ap.config(cfg, save)`
|
|
|
|
#### Parameters
|
|
- `cfg` table to hold configuration:
|
|
- `ssid` SSID chars 1-32
|
|
- `pwd` password chars 8-64
|
|
- `auth` authentication method, one of `wifi.AUTH_OPEN`, `wifi.AUTH_WPA_PSK`, `wifi.AUTH_WPA2_PSK` (default), `wifi.AUTH_WPA_WPA2_PSK`
|
|
- `channel` channel number 1-14 default = 11
|
|
- `hidden` false = not hidden, true = hidden, default = false
|
|
- `max` maximum number of connections 1-4 default=4
|
|
- `beacon` beacon interval time in range 100-60000, default = 100
|
|
- `save` save configuration to flash.
|
|
- `true` configuration **will** be retained through power cycle. (Default)
|
|
- `false` configuration **will not** be retained through power cycle.
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### Example:
|
|
```lua
|
|
cfg={}
|
|
cfg.ssid="myssid"
|
|
cfg.pwd="mypassword"
|
|
wifi.ap.config(cfg)
|
|
```
|
|
|
|
|
|
## wifi.ap.on()
|
|
|
|
Registers callbacks for WiFi AP events.
|
|
|
|
#### Syntax
|
|
`wifi.ap.on(event, callback)`
|
|
|
|
#### Parameters
|
|
- `event` WiFi AP event you would like to set a callback for:
|
|
- "start"
|
|
- "stop"
|
|
- "sta_connected"
|
|
- "sta_disconnected"
|
|
- "probe_req"
|
|
- `callback` callback `function(event, info)` to perform when event occurs,
|
|
or `nil` to unregister the callback for the event. The `info` argument
|
|
given to the callback is a table containing additional information about
|
|
the event.
|
|
|
|
Event information provided for each event is as follows:
|
|
|
|
- `start`: no additional info
|
|
- `stop`: no additional info
|
|
- `sta_connected`: information about the client that connected:
|
|
- `mac`: the MAC address
|
|
- `id`: assigned station id (AID)
|
|
- `disconnected`: information about disconnecting client
|
|
- `mac`: the MAC address
|
|
- `id`: assigned station id (AID)
|
|
- `probe_req`: information about the probing client
|
|
- `from`: MAC address of the probing client
|
|
- `rssi`: Received Signal Strength Indicator value
|
|
|
|
## wifi.ap.getmac()
|
|
|
|
Gets MAC address in access point mode.
|
|
|
|
#### Syntax
|
|
`wifi.ap.getmac()`
|
|
|
|
#### Parameters
|
|
None
|
|
|
|
#### Returns
|
|
MAC address as string e.g. "18:fe:34:a2:d7:34"
|
|
|
|
## wifi.ap.setip()
|
|
|
|
Sets IP address, netmask, gateway, dns address in AccessPoint mode.
|
|
|
|
Options set by this function are not saved to flash.
|
|
|
|
#### Syntax
|
|
`wifi.ap.setip(cfg)`
|
|
|
|
#### Parameters
|
|
- `cfg` table to hold configuration:
|
|
- `ip` device ip address.
|
|
- `netmask` network netmask.
|
|
- `gateway` gateway address.
|
|
- `dns` name server address, which will be provided to clients over DHCP. (Optional)
|
|
|
|
#### Returns
|
|
`nil`
|
|
|
|
#### Example
|
|
```lua
|
|
cfg={}
|
|
cfg.ip=192.168.0.10
|
|
cfg.netmask=255.255.255.0
|
|
cfg.gateway=192.168.0.1
|
|
cfg.dns=8.8.8.8
|
|
wifi.ap.setip(cfg)
|
|
```
|
|
|
|
## wifi.ap.sethostname
|
|
|
|
Sets AccessPoint hostname.
|
|
|
|
Options set by this function are not saved to flash.
|
|
|
|
#### Syntax
|
|
`wifi.ap.sethostname(hostname)`
|
|
|
|
#### Returns
|
|
true if success, false otherwise
|
|
|
|
#### Parameters
|
|
`hostname` must only contain letters, numbers and hyphens('-') and be 32 characters or less with first and last character being alphanumeric
|
|
|
|
#### Example
|
|
```lua
|
|
wifi.ap.sethostname("ESP32")
|
|
```
|