22450a6fe7
roundedPlate: Fix placement
2020-02-28 17:52:49 +01:00
6476a51fc4
roundedPlate: Fix callback positioning
2020-02-28 17:52:49 +01:00
223ac26122
roundedPlate: new extend_corners param
2020-02-28 17:52:18 +01:00
26b33d62ff
roundedPlate: Properly lookup edge
2020-02-28 17:46:44 +01:00
7c004e2d2c
New primitive: Boxes.step()
...
Outset a line by a given margin - negative values for insetting
2020-02-28 17:46:44 +01:00
a0338a559f
Add a bottom to the divider tray.
...
This add support for the generation of a bottom for the divider tray.
The bottom can be generated by passing the --bottom=True flag.
This makes it possible to generate ./static/samples/DividerTray.jpg
2020-02-26 21:00:26 +01:00
eeb1baf352
Gear: don't allow less than 2 teeth
2020-02-01 15:30:53 +01:00
0394d418c1
dHole: Prevent division by zero
2020-02-01 15:30:18 +01:00
7943fa2390
flex2D: Fix division by zero for too small patterns
2020-02-01 15:22:35 +01:00
ec9d911142
DividerTray: Use ValueError instead of assert to treat this as wrong user input
2020-02-01 15:17:18 +01:00
069dd853aa
BinTray: limit front parameter
2020-02-01 15:14:12 +01:00
95f2fbeb82
corner(): Make more robust against division by zero
2020-02-01 15:03:49 +01:00
2121228036
TrayLayout: Error out if tray is just a single wall
2020-02-01 14:51:38 +01:00
f8401aac75
rectangularRectangle: Make angle calculation more robust
2020-02-01 14:43:45 +01:00
2a7e1e62d1
PaintStorage: Prevent division by zero
2020-02-01 14:31:24 +01:00
dd0f2d748c
ChestHingeSettings: check pin_height for minimal size
2020-02-01 14:27:17 +01:00
0f3eb5b21a
StackableSettings: check angle for invalid values
2020-02-01 14:16:26 +01:00
9706816fe4
gears: prevent division by zero
2020-02-01 13:59:30 +01:00
37bff9d358
fixed d3 diameter (mounting screw holes)
2020-01-22 16:11:18 +01:00
1f3110c6fa
New generator: TriangleLamp
2020-01-21 21:34:02 +01:00
10e2085eef
Remove Python 2 compat foo
2019-12-21 17:47:54 +01:00
4d53bd17cc
partsMatrix: support width=0 for all parts in one row
2019-12-16 20:07:30 +01:00
e2b87af2a4
UniversalBox: Add outside parameter
...
Fixes : #144
2019-12-14 19:13:40 +01:00
aba9631b00
Make joints of box sides go to the very bottom
...
for NotesHolder, TypeTray and UniversalBox.
The same should be done to many other boxes as soon as they get the
bottom_edge parameter
Resolves : #111
2019-12-14 14:18:38 +01:00
8cb5a8e042
Check values of flex settings
2019-12-14 13:09:43 +01:00
fe9555a79f
checkValues
2019-12-14 13:09:43 +01:00
c5474e7488
DiscRack: Limit lower_factor and rear_factor to smaller than one
2019-12-14 12:23:08 +01:00
024b574763
TrayLayout: Add default for layout param
2019-12-14 12:14:24 +01:00
093e10a3ac
AngledBox: Use FingerJointSettings for vertical edges, too
2019-12-06 23:37:22 +01:00
bd1db150c7
New geneator: SpicesRack
2019-11-29 19:58:27 +01:00
182d222f01
Prevent not having any sections at all for argparseSections
2019-11-24 19:10:35 +01:00
d2d97b01c9
grip(): Prevent division by zero
2019-11-24 16:42:47 +01:00
9f8b84b3f1
add parameters for banana socket and flipswitch diameters
2019-11-20 11:57:13 +01:00
2c367562a9
remove commented code
2019-11-20 11:57:13 +01:00
90fdf897a9
formatting: whitespace cleanup
2019-11-20 11:57:13 +01:00
c67d1f874c
StorageShelf: Add retainer_hole_edge param
...
to allow strengthening the retainer walls by using an h edge.
Also use a h edge on the bottom retainer wall if selected as bottom_edge.
2019-11-09 23:32:12 +01:00
e8cda89381
StorageShelf: Fix holes for inner vertical walls
2019-11-09 23:31:26 +01:00
71711baa1a
StorageShelf: Add retainer wall
...
This patch does not add finger joints to the vertical walls to attach the
retainer walls as the walls are likely to be to small to be able to make use
of them. In hte long run they should be added, though.
2019-11-09 17:10:23 +01:00
0cdc930459
StorageShelf: Change front edge from E to e
...
This makes the shelf one thickness less deep - as it should be
2019-11-09 16:10:30 +01:00
923798beb9
SBCMicroRack: Fix dowel diameter
2019-11-07 15:38:16 +01:00
2860a32360
SBCMicroRack: Comment out unfinished fan parameter
2019-11-07 15:38:16 +01:00
d9c190073b
SBCMicroRack: Don't draw bottom fingerholes twice
2019-11-07 15:38:16 +01:00
af6c9be8f7
SBCMicroRack: Rearrange parts
2019-11-07 15:38:16 +01:00
569eb2f49c
New generator: SBCMicroRack
2019-11-07 15:37:57 +01:00
199251ae52
Add lid for StackableEdge (S) as top_edge
2019-11-04 17:13:12 +01:00
83b5363bc8
StackableEdge: Fix margin for upper (S) variant
2019-11-04 17:05:18 +01:00
4ac46840d2
NotesHolder: Fix various issues
...
Code for opening == 0.0 was broken (See #187 )
Fixed placement of bottom
Fixed margin of USlotEdge
Resolves : #187
2019-11-04 08:52:26 +01:00
927f483c19
New generator: LaserHoldfast - A holdfast for honey comb tables
2019-10-19 23:47:44 +02:00
e2cb90db89
NotesHolder: Split front into two pieces and set better default values
...
Resolves : #129
2019-10-19 21:49:43 +02:00
b0b35d6084
Mention BurnTest in docs and in the burn parameter description
2019-10-19 12:29:56 +02:00
cfbcbb065c
Clarify doc string for FingerJointSettings.play
2019-10-19 12:03:57 +02:00
011024f0a4
TrayLayout: Add comment to clarify the purpose of the classes
...
Resolves : #179
2019-10-18 19:06:07 +02:00
228335a993
BurnTest: fix part placement
2019-10-13 18:42:40 +02:00
89ea774a39
New generator: BurnTest
2019-10-13 18:39:06 +02:00
13ecfc9914
Support springs for finger joints (FingerJointSettings.style)
...
Resolves : #177
2019-10-11 22:32:57 +02:00
f5ed90ca88
SlatwallWrenchHolder: Add extra_distance parameter for Jonas
2019-10-10 20:00:22 +02:00
8afdfdf3f5
New generator: BaynonetBox
2019-09-23 23:44:02 +02:00
877915eb74
Arcade: Make height of monitor and depth of keyboard adjustable
...
Resolves : #166
2019-09-23 21:42:57 +02:00
d6495fc7b4
DrillBox: Fix font size
...
Now that the text() function has a fontsize parameter, setting the font size
on ctx before calling text() has no impact.
Resolves : #173
Thanks to Marko Luther for reporting and suggesting this fix!
2019-09-23 12:15:49 +02:00
3ba90c517c
TrayLayout: Fix cli
...
TrayLayout was still trying to produce a drawing and failed. Now TrayLayout is
not using most of the infrastructure and only TrayLayout2 has the capacity to
create a drawing.
Resolves : #172
2019-09-22 22:37:33 +02:00
b124c96c63
UnevenHeightBox: Use lid and bottom_egde for height calculation
...
when "outside" is set
2019-09-08 23:26:23 +02:00
657b978aa0
StorageShelf: Use top and bottom_egde for height calculation with "outside" set
2019-09-08 23:26:23 +02:00
605692f751
StorageRack: Use top and bottom_egde for height calculation with "outside" set
2019-09-08 23:26:23 +02:00
5c0cc4d732
SlatwallTypeTray: Remove unused code carried over from TypeTray
2019-09-08 23:26:23 +02:00
2b0bdde145
SlatwallTypeTray: Adjust height according to bottom_edge if outside selected
2019-09-08 23:26:23 +02:00
52484b0d55
adjustSize(): add support for edge chars
2019-09-08 23:26:23 +02:00
6c9d23af6e
New generator DividerTray
2019-08-30 21:00:32 +02:00
c3185f5129
Rename to Rack19HalfWidth to better fit with other Rack boxes
...
Move to Box group
Support more than one row of equipement
Move defaults to arguments to conform with general coding style
2019-08-30 12:27:13 +02:00
681ebbb694
add h19rack for a ported half 19inch rackmount
2019-08-30 11:58:21 +02:00
9a17e3efa9
Precompile optimizations REs and fix performance issue
2019-08-22 00:31:45 +02:00
39bd912c90
Harden Extend.addPoint for None arguments
2019-08-18 14:46:13 +02:00
9db79243f8
Make Slide-on Lid with pin easier to insert
...
Make slot half a thickness wider and round the corners
Resolves : #156
Thanks to Matthijs Kooijman for suggesting this change!
2019-08-17 00:05:13 +02:00
0409bcbe65
Fix SVG merging for Inkscape
...
Resolves : #163
2019-08-16 22:37:42 +02:00
65d2293e25
Fix Extend.__add__ for None values
2019-08-15 23:12:35 +02:00
02988d12c5
Catch exceptions from failed ps2edit calls
2019-08-15 23:12:35 +02:00
c81d23e605
SlatwallDrillBox: Fix all kind of errors
2019-08-15 23:12:35 +02:00
e4bdc190bb
Flexbox3: Fix lid length
2019-08-08 22:53:08 +02:00
73422b0faf
Fix name space handling in new svg code
2019-07-31 23:40:48 +02:00
6a3a9b984a
SlatwallTypetray: Fix side joints of front wall (F -> f)
2019-07-31 23:40:06 +02:00
8ecf04cbe8
Fix handling of space in LidSideRight/Left
...
Previously, the extra space was added above the first pin and below the
(optional) second pin. This would cause the lid to misalign with the
holes in the back wall, making it harder to close the lid.
With this commit, the extra space is divided evenly above and below the
nominal position of the pin.
For this to work, the startwidth (or endwidth, depending on the side) is
slightly adjusted (since the start of the first pin slot is actually
generated by the adjacent edge). This moves the starting point, so the
location of the spring hole is adjusted to compensate for that.
2019-07-27 13:30:06 +02:00
3bd4dc9907
Fix spring hole offsets by burn in LidSideRight/Left
2019-07-27 13:30:06 +02:00
4691a65a29
Let LidSideRight/Left respect edge_width
...
This allows modifying the height of the wall that extends above the lid.
The box back wall (with holes) would already support edge_width, so this
makes it supported on all three walls where needed.
2019-07-27 13:30:06 +02:00
db1da4ec12
Fix hole positions offset by burn in FingerHoleEdge
...
When rendering the FingerHoleEdge, the current position would be
corrected for burn (e.g. it would be on the center of the laser path,
rather than the actual edge of the final part). However, the FingerHoles
class (or actually the rectangularHole method called by it) that draws
the actual holes already corrects for burn, which caused the hole
position to be offset by the burn value.
This offset was particularly problematic when making a sliding lid,
since the holes would not align perfectly with the lid, making it hard
to close the lid. With this change, the sliding slots in the side walls
and the holes in the back wall align perfectly (though only when the lid
settings have zero play, which is a separate problem).
This commit fixes FingerHoleEdge (and its subclass LidHoleEdge), but
there might be other users of the FingerHole class (usually indirectly
through boxes.fingerHolesAt) that still have the same problem.
2019-07-27 13:30:06 +02:00
eeb2c344d5
Clarify where l and L edges should be used
2019-07-27 13:30:06 +02:00
ca1a3575d0
forward holesSettings to hexHolesRectangle from within rectangularWall
2019-07-21 01:21:55 +02:00
c06b95d2d0
link: http -> https
2019-07-20 00:23:29 +02:00
0a55e9ca6b
Optimize SVG paths
...
Resolves #63
2019-07-19 21:49:55 +02:00
a38254667c
Remove no longer needed line in _template.py
2019-07-18 20:55:07 +02:00
17d7cd80ab
Don't show generators in modules starting with underscore (templates)
2019-07-12 00:47:09 +02:00
11174f2ecc
New generator SlatwallDrillBox
2019-07-12 00:43:06 +02:00
88e99a5726
New generator: FlexBox5
...
Resolves #147
2019-07-12 00:24:50 +02:00
e6f431ab15
New generator: MakitaPowerSupply
2019-07-07 16:26:29 +02:00
fff74cf382
Add metadata as a xml comment
...
Resolves #66
2019-07-07 13:43:04 +02:00
a19debf1bd
Rename remaining Slatwall generators from Sw* to Slatwall*
2019-07-04 22:59:32 +02:00
573b630adc
New generator: SlatwallPlaneHolder
2019-07-04 22:39:34 +02:00
31d46088c2
Move drawing to origin for SVGs
2019-07-04 17:52:28 +02:00
635a42a25e
Use eTree to caclulate the eytend of the drawing
...
Also check symbols (text character) now
2019-07-04 17:52:28 +02:00
d162c769b4
Use built in eTree implementation instead of lxml
2019-07-04 17:52:08 +02:00
4a9cdc8d8e
Switch to eTree as a xml library (instead of minidom)
2019-07-04 17:48:53 +02:00
443c8a1c38
properly rewrite svg viewPort using minidom for xml
...
This avoids raising the 'Not enough space for size' exception.
2019-07-04 17:48:53 +02:00
abdab6866a
New generator: StorageRack - Box with rails to slide other boxes in
2019-06-30 20:53:42 +02:00
2f7603b4b4
New generator: SlatWallWrenchHolder
2019-06-30 20:53:42 +02:00
0105957c05
New generator: SlatWallChiselHolder
2019-06-30 17:19:02 +02:00
138dffbf2a
New generator: SlatWallCaliperHolder
2019-06-30 15:48:09 +02:00
be8aed394a
New generator: Slatwall PlaneHolder
2019-06-30 15:18:11 +02:00
09df973d69
New generator: SlatwallConsole - an outset and angled plate to mount stuff to
2019-06-22 00:07:23 +02:00
810c3dbe3e
New generator: SwTypeTray - a tray to hang at a slat wall
2019-06-22 00:05:57 +02:00
f1ce996aae
New generator: SwPliersHolder - a bar to hang pliers on
2019-06-22 00:04:30 +02:00
6c85ae7ea2
Add trapezoidSideWall() that supports radius param for additional strength
2019-06-21 23:16:59 +02:00
6a809e17e7
Move trapezoidWall() from UnevenHeightBox to Boxes class
2019-06-21 21:37:57 +02:00
01ca56fdce
Support all different section syntaxes (sx, sy, ...) side by side
2019-06-21 21:37:57 +02:00
db706fc939
SlatWall edges: Make bottom hook selectable, various fixes
2019-06-21 21:36:28 +02:00
1e35a3b9ed
New generator: SwSlottedHolder
...
A tool holder for slat wall
2019-06-21 21:22:10 +02:00
5cef906a9a
Add SlatWallHoleEdge (dD) classes
...
Similar to FigerHolesEdge (h)
2019-06-21 18:47:29 +02:00
9415a6864f
Add boxes/generators/_swtemplate.py as a starting point for Slat Wall boxes
2019-06-13 19:02:02 +02:00
aadf5ceafc
Add Edge types, example and UIGroup for slat wall compatible boxes
2019-06-13 19:00:32 +02:00
753422fa46
New generator DiscRack
...
A rack for storing disk-shaped objects vertically next to each other
2019-06-01 13:09:01 +02:00
e8e248994b
Add a StorageSelf generator. This is a shelf for storing TypeTray boxes.
...
It is based on TypeTray generator. The sh parameter replace the sx parameter.
It is not a subclasse of TypeTray in order to have the top and bottom at
the right place.
2019-06-01 12:52:34 +02:00
a6ca723759
Mirror holes on the other walls
...
to have them match up. Otherwise boxes with non symetric top edges don't fit
together.
Fixes #141
2019-05-11 17:18:10 +02:00
46157b2030
Add .mirrorX() and .mirrorY() wrappers
...
These are especially useful for warpping callbacks.
2019-05-11 17:17:11 +02:00
93c2093ef3
AllEdges: Fix spacing and add edegs around the corner
...
to make it more clear which direction the edges are pointing.
Related #132
2019-04-14 18:17:09 +02:00
f22be6f6d5
Fix polygonWalls for inner corners
2019-04-14 18:17:09 +02:00
0b781ce7ef
Add turtle param to polygonWall
...
to allow using it as turtle graphic command instead of a part
2019-04-14 18:17:09 +02:00
dc11929258
Fix _polygonWallExtend for corners with negative angles
2019-04-14 18:17:09 +02:00
95dba0dee7
box: raise NotImplementedError
...
NotImplemented is a sentinel for comparisons; encountering this as an
exception would result in a meta-error.
2019-04-10 17:56:12 +02:00
ce8576d39e
New generator: HeartBox
2019-03-24 21:52:26 +01:00
7aec26e893
New .polygonWall() part
...
Similar to .polyline() but with (f) edges on the outside
.polygonWalls draws the surrounding walls
2019-03-24 21:50:36 +01:00
4f4d947253
.corner(): Fix tabs for small arcs
2019-03-24 21:50:11 +01:00
f178215f20
.corner(): Also accept (angle, radius) tuples
2019-03-24 21:50:11 +01:00
c09ee50fbd
New generator: NotesHolder
2019-03-23 12:36:21 +01:00
8bacd1f766
UniversalBox: Fix missing lids for various top_edges
...
Call got refactored away
Resolves : #121
2019-02-27 22:58:05 +01:00
fb4791f803
Fix typo in help text for tabs
2019-02-26 00:02:30 +01:00
cbb000f12e
DoveTailJoint: remove no longer needed ctx.translate
2019-02-24 14:45:57 +01:00
abed8c06ac
FingerHoles: use .saved_context()
2019-02-24 14:42:48 +01:00
72617110cf
FingerHoleEdge: Use modern code and add tab support
2019-02-24 13:14:21 +01:00
eb5f3008da
RoundedTriangleEdge: Add tabs
2019-02-24 12:16:47 +01:00
8640514daf
Omit reference for svg_Ponoko format
2019-02-14 21:36:54 +01:00
8db3942757
UniversalBox: Fix positioning of lid parts
2019-02-14 21:32:27 +01:00
25ea02d317
Handle the drawing reaching into the negative x axis properly
2019-02-14 21:15:28 +01:00
c6e872a146
Add tabs to .parts
2019-02-14 17:34:22 +01:00
81708bbbca
.polyline: mention tabs feature in doc string
2019-02-14 17:32:59 +01:00
3a0e34eed8
Fix NutHole which broke after switching over to saved_context
2019-02-14 17:31:56 +01:00
679234afd3
Fix docstrings of .open() and .close() to match new use pattern
2019-02-13 09:04:57 +01:00
9b1ce265bf
Make docstrings ready for autodoc
2019-02-13 09:01:20 +01:00
e3ba617f22
Fix traceback for top_edge == "L"
...
No longer access the t1 edge type after changing it which may lead
to t1 being a char instead of a Edge instance
Thanks to michael (https://hackaday.io/hacker/381347-michael ) for
pointing this out!
2019-02-10 19:49:51 +01:00
0d07f48b7f
Remove .open() call from the .render() method
...
Having this call there was necessary in the past as the open() method would
need the canvas size as a parameter. This is now determined automatically
after rendering.
Still calling open() is deprecated but won't result in an error.
2019-02-08 17:43:15 +01:00
861c8451e2
Remove call to .close() from .render() method
...
There is really no need for all the generator to care
Still calling it is deprecated but won't result in an error
2019-02-08 17:32:04 +01:00
2ba6fa1bf3
Use .saved_context() instead of .ctx.save() and .restore()
2019-02-07 22:43:04 +01:00
1724f67bdf
Delete never to be finished printer generator
...
This should have become a 3D printer using strings in a delta configuration.
2019-02-07 22:43:04 +01:00
ded5addbe9
Remove no longer needed calls to ctx.stroke()
...
Boxes.move() take care of that nowadays
2019-02-07 22:43:04 +01:00
80ab24dceb
Fix format of doc strings
2019-02-07 17:42:41 +01:00
c5d434105b
Add svg_Ponoko output format
...
This is just regular SVG with Ponoko-specific line properties
Yes, the lines are too thin to be seen in a regular web browser.
Resolves : #112
2019-02-03 16:30:28 +01:00
abacdd486e
Implement proper color handling
...
Avoid accessing Boxes.ctx (the cairo context) all over the code.
Have named colors
2019-02-03 16:28:02 +01:00
c573914bcd
Add Boxes.saved_context() context manager
...
Avoid directly accessing Boxes.ctx (the cairo context) all over the place.
Also have a more modern API for returning to a previous spot.
2019-02-03 16:25:31 +01:00
acb457be2a
Add GPL copy right header
2019-02-02 18:05:04 +01:00
2e5a19a40f
Python 2 compat fix
2019-01-12 18:42:44 +01:00
6f4e94577b
New generator: RectangularWall
2019-01-12 15:28:17 +01:00
dac6b3ac3d
Fix Edge descriptions
...
Add descriptions for edges that don't have their own class
Make ChestHingeFront sub class of Edge as BaseEdge no longer draws anything
2019-01-12 15:28:17 +01:00
1739d11af5
Doc string for GearSettings
2019-01-12 15:28:17 +01:00
d0356a12a3
Add parameters to addTopEdgeSettings() for changed defaults
2019-01-12 00:07:37 +01:00
ba3cacbf93
RoundedTriangleEdge: Add outset setting
2019-01-12 00:07:22 +01:00
2747d9719a
Add RoundedTriangleEdge to top_edges
2019-01-12 00:00:55 +01:00
31fd0024ee
Add RoundedTriangleEdge t
...
Based on the Caddy generator by bobm123 in the PR #14
(https://github.com/florianfesti/boxes/pull/14 )
Edge will be added to the TypeTray generator to achieve similar results as Caddy
Co-authored-by: bobm123 <bobm123@gmail.com>
2019-01-11 23:56:28 +01:00
64fb498e6e
UniversalBox: Use a more robust way of placing the pieces
...
No longer rely on all side walls having the same height
2019-01-11 19:41:02 +01:00
97e7e3b68f
TypeTray: Swap vertical edge types to match the layout of the UniversalBox
2019-01-11 19:41:02 +01:00
5c70515f01
TypeTray: Add lids matching top_edge
2019-01-10 22:27:36 +01:00
371097aa89
PaintStorage: Make grip hole smaller and more rounded
...
Fixes #108
2019-01-10 22:09:45 +01:00
c0a782b745
TypeTray: Add support for all top_edges
2019-01-03 11:13:27 +01:00
c2615d4b38
TypeTray: rearrange parts
2018-12-27 17:19:10 +01:00
73050d4969
Make .continueDirection() more private
2018-12-22 17:23:33 +01:00
2df63b6ec8
ShutterBox: Add style with two rounded corners
...
Move generator to FlexBox category
2018-12-19 18:04:34 +01:00
879b3149bb
New generator: ShutterBox
...
A box with a rolling shutter made out of flex
2018-12-13 18:39:01 +01:00
4a79c37e71
CardBox: Add gripping ledge to the lid
2018-12-11 19:33:52 +01:00
4d2592fecf
Add e edge to bottom_edge selection
2018-12-08 18:22:13 +01:00
fd956d1f08
rectangularHole(): clamp corner radius to available space
2018-12-08 12:42:36 +01:00
8f03030c53
PaintStorage: Add carrying hole
2018-12-08 12:37:20 +01:00
925c6ce6dc
PaintStand: Fix previous change
2018-11-24 22:47:35 +01:00
17e4eb8563
PaintStorage: Fix heights
2018-11-15 22:10:19 +01:00
ed6855d79c
RoundedPlate: Call first callback only once
...
Remove left over call to .cc()
2018-11-09 21:01:00 +01:00
d85fa4e849
LaserClamp: Improve design
...
Extend bottom bracket and add hook
Use only one bottom bracket
Add finger ring to allow easier placement
Improve top hook
2018-11-05 22:08:23 +01:00
0f999a89ad
New generator: AllEdges showing all the standard edge types
2018-11-05 21:38:49 +01:00
b7bd6306d1
Fix division by zero in FlexEdge
2018-11-05 21:38:49 +01:00
fe89528e05
PaintStorage: Add support for hexagonal hole patterns
2018-10-29 18:16:16 +01:00
36077e6cb0
PaintStorage: Optimize part placement
2018-10-29 15:44:18 +01:00
c28541a977
Add a generator for paintstand
...
A simple stackable paintstand, very much inspired by:
https://www.youtube.com/watch?v=6HJarJg1npk
2018-10-29 15:11:35 +01:00
e95f36a18a
Parameterize Silverwarebox
...
Make the messurements selectable
2018-10-28 13:19:37 +01:00
80288079af
New generator: TwoPiece
...
Based on a generator with the same name by bobm123<bobm123@gmail.com>
2018-10-25 22:35:20 +02:00
5b93c1228d
CardBox: Add num param for the number of decks
2018-10-25 17:36:46 +02:00
5a13fbea8b
Add DisplayCase generator
2018-10-24 21:28:54 +02:00
2060293cf3
New generator: RoyalGame of Ur
2018-10-24 21:23:57 +02:00
397cc81690
FlexBox3: Use .move()
...
Use .edgeCorner() instead of own implementation
2018-10-19 22:12:13 +02:00
f7c2d91e42
FlexBox2: Make latchsize configurable
2018-10-19 21:46:30 +02:00
417a053ad3
FlexBox2: Use .move()
2018-10-19 21:45:26 +02:00
4d76457d3a
FlexBox: Make latchsize configurable
2018-10-19 21:35:11 +02:00
791ef0fdca
FlexBox: Use .move()
2018-10-19 21:33:52 +02:00
a9009732ac
FlexBox4: Make latchsize configurable
2018-10-19 19:20:23 +02:00
4ba18d87b7
FlexBox4: Modernize a bit and use .move()
2018-10-19 19:15:55 +02:00
a4b5af98e2
Add new "mirror" key word to the where parameter of Boxes.move()
2018-10-19 19:05:07 +02:00
c45b5cd30b
Add debug rectangle for move commands
2018-10-19 18:58:29 +02:00
1cf671ddd2
FlexBox4: Calculate length of flex after adjusting the radius
2018-10-19 10:02:16 +02:00
Florian Festi
Erwin Jansen
Stefan Reichhard
Marius Bergmann
gmorell
Guillaume Collic
Stefan Schwarz
Matthijs Kooijman
Marko Luther
Rotzbua
Stefan Grosshauser
chrysn
Germain Lemasson
Martin Müller
Wayne Wylupski
jens persson
Alexander Bulimov